Running The Ping Test; Resetting To The Default Configuration - Cisco Aironet 1130AG Series Hardware Installation Manual

Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
3-14 3-14
Chapter 3 3 Chapter Troubleshooting Troubleshoo

Running the Ping Test

Running the Ping Test
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6

Resetting to the Default Configuration

Resetting to the Default Configuration
Note Note
Hardware Installation Guide
ting Autonomous Autonomous Access Access Points Points
You can use the ping test to evaluate the link to and from an associated wireless device. The ping test You can use the ping test to evaluate the link to and from an associated wireless device. The ping test
provides two modes of operation: provides two modes of operation:
a. a. Performs a test using a specified number of packets and then displays the test results. Performs a test using a specified number of packets and then displays the test results.
b. b. Performs a test that continuously operates until you stop the test and then displays the test results. Performs a test that continuously operates until you stop the test and then displays the test results.
Follow these steps to activate the ping test: Follow these steps to activate the ping test:
Use your web browser to access the access point browser interface. Use your web browser to access the access point browser interface.
Click Click Association Association and the main association page appears. and the main association page appears.
Click the MAC address of an associated wireless device and the Statistics page for that device appears. Click the MAC address of an associated wireless device and the Statistics page for that device appears.
Click the Ping/Link Click the Ping/Link T T est est tab and the Ping/Link Test page appears. tab and the Ping/Link Test page appears.
If you want to specify the number of packets to use in the test, follow these steps: If you want to specify the number of packets to use in the test, follow these steps:
a. a. Enter the number of packets in the Number of Packets field Enter the number of packets in the Number of Packets field
b. b. Enter the packet size in the Packet Size field and click Enter the packet size in the Packet Size field and click Start
If you want to use a continuous test, follow these steps: If you want to use a continuous test, follow these steps:
a. a. Enter the packet size in the Packet Size field. Enter the packet size in the Packet Size field.
b. b. Click Click Start Start to activate the test. to activate the test.
c. c. Click Click Stop Stop to stop the test. to stop the test.
When the test has completed, the test results are displayed at the bottom of the page. You should check When the test has completed, the test results are displayed at the bottom of the page. You should check
for any lost packets that can indicate a problem with the wireless link. For best results, you should also for any lost packets that can indicate a problem with the wireless link. For best results, you should also
perform this test several times. perform this test several times.
If you forget the password that allows you to configure the access point, you may need to completely If you forget the password that allows you to configure the access point, you may need to completely
reset the configuration. You can use the MODE button on the access point or t reset the configuration. You can use the MODE button on the access point or t he web-browser interface.
The following steps reset The following steps reset all all configuration settings to factory defaults, including passwords, WEP keys,
the IP address, and the SSID. the IP address, and the SSID.
For additional information on ac cess point default behavior, refer to the For additional information on ac
sect section on pag ion on page e 3-4 and the 3-4 and the "Defaul
configuration settings to factory defaults, including passwords, WEP keys,
cess point default behavior, refer to the "Default IP Address Behavior"
"Default SSID and Radio Behavior" secti t SSID and Radio Behavior"
Running the Ping Test Running the Ping Test
Start. .
he web-browser interface.
"Default IP Address Behavior"
section on page on on page 3-4. . 3-4
OL-8369-04 OL-8369-04