Configuring The Access Point System Power Settings Using A Browser - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04
Low Power Condition for Autonomous Access Points Low Power Condition for Autonomous Access Points

Configuring the Access Point System Power Settings Using a Browser

Configuring the Access Point System Power Settings Using a Browser
Note Note
Note Note
Caution Caution
T T ab able le 3- 3-3 3 A A cc cces
P P o o w w e e r r S S o o u u r r c c e e
A A C C p p o o w w e e r r m m o o d d u u l l e e
Cisco switch that supports Cisco switch that supports
Intelligent Power Management Intelligent Power Management
Cisco switch that does not Cisco switch that does not
support Intelligent Power support Intelligent Power
1 1
Management Management
You can also use your browser to set the access point System Power Settings. You can also use your browser to set the access point System Power Settings.
The access point web-browser interface is fully compatible with Microsoft Internet Explorer version 6.0 The access point web-browser interface is fully compatible with Microsoft Internet Explorer version 6.0
on Windows 98 and 2000 platforms and with Netscape version 7.0 on Windows 98, Windows 2000, and on Windows 98 and 2000 platforms and with Netscape version 7.0 on Windows 98, Windows 2000, and
Solaris platforms. Solaris platforms.
When using the access point browser interface, you should disable your browser pop-up blocker. When using the access point browser interface, you should disable your browser pop-up blocker.
Figur ure Fig e 3- 3-2 2 shows the system power setting options and indicates the power status of the access point. shows the system power setting options and indicates the power status of the access point.
F F i i g g u u r r e e 3 3 - - 2 2 S S y y s s t t e e m m P P o o w w e e r r S S e e t t t t i i n n g g s s
If the access point receives power through PoE, the output current of the power sourcing equipment If the access point receives power through PoE, the output current of the power sourcing equipment
(PSE) cannot exceed 400 mA per port. The power source must comply with IEEE802.3af or IEC60950 (PSE) cannot exceed 400 mA per port. The power source must comply with IEEE802.3af or IEC60950
for limited power sources. for limited power sources.
T T able abl e 3-3 3-3 lists the access point system power settings and the Cisco switch p lists the access point system power settings and the Cisco switch p ower commands for several
power options. power options.
ess P s Poi oint nt S S ys yste tem P m Po o we wer S r Set etti ting
A A c c c c e e s s s s P P o o i i n n t t S S y y s s t t e e m m P P o o w w e e r r S S e e t t t t i i n n g g s s
C C o o n n f f i i g g u u r r a a t t i i o o n n c c h h a a n n g g e e s s a a r r e e n n o o t t r r e e q q u u i i r r e e d d
Power Settings: Power Settings:
1 1
Power Negotiation (selected) Power Negotiation
Power Injector: Power Injector:
Installed on Port with MAC Address Installed on
Power Settings: Power Settings:
Pre-standard Compatibility (selected) Pre-standard Compatibility
Power Injector: Power Injector:
Installed on Port with MAC Address Installed on
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
ngs a s and nd Ci Cisc sco S o Swi witc tch C h Com omma mand
(selected)
Port with MAC Address (unchecked) (unchecked)
(selected)
Port with MAC Address (unchecked) (unchecked)
Point Hardware Installation Guide
Chapter 3 3 Chapter Troubleshooting Autonomous Troubleshooting Autonomous Access
ower commands for several
nds s
Cisco Switch Cisco Switch
Power Command Power Command
power inline never power inline never
power inline auto power inline auto
power inline auto power inline auto
3-11 3-11
Access Points Points