Enable Radio Interfaces; Ssid; Security Settings - Cisco Aironet 1130AG Series Hardware Installation Manual

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access Point
3-4 3-4
Chapter 3 3 Chapter Troubleshoo Troubleshooting

Enable Radio Interfaces

Enable Radio Interfaces
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6
St Step ep 7 7
St Step ep 8 8
St Step ep 9 9
St Step ep 10 10

SSID

SSID
Note Note
WEP WEP Keys Keys

Security Settings

Security Settings
Hardware Installation Guide
ting Autonomous Autonomous Access Access Points Points
To enable the radio interfaces, follow these instructions: To enable the radio interfaces, follow these instructions:
Use your web-browser to access your access point. Use your web-browser to access your access point.
When the Summary Status page displays, click When the Summary Status page displays, click Network Interfaces > Radio0-802.11B
Radio0-802.11G and the radio status page displays. Radio0-802.11G and the radio status page displays.
Click Settings Click Settings and the radio settings page displays. and the radio settings page displays.
Click Click Enable Enable in the Enable Radio field. in the Enable Radio field.
Click Click Apply Apply. .
Click Click Network Interfaces > Radio0-802.11A Network Interfaces > Radio0-802.11A and the radio status page displays.
Click Settings Click Settings and the radio settings page displays. and the radio settings page displays.
Click Enable Click Enable in the Enable Radio field. in the Enable Radio field.
Click Apply Apply. .
Click
Close your web-browser. Close your web-browser.
Wireless clients attempting to associate with the access point must use the same SSID as the access point. Wireless clients attempting to associate with the access point must use the same SSID as the access point.
If a client device's SSID does not match the SSID of an access point If a client device's SSID does not match the SSID of an access point in radio range, the client device will
not associate. The access point default SSID is tsunami not associate. The access point default SSID is
Guide for Cisco Aironet Access Points Guide for Cisco Aironet Access Points for instructions on how to configure an SSID.
The default SSID ( The default SSID ( tsunami tsunami ) is not supported in access points running Cisco IOS Release 12.3(4)JA or
later. You must configure an SSID before client devices can associate to the access point. later. You must configure an SSID before client devices can associate to the access point.
The WEP key you use to transmit data must be set up exactly the same on your access point and any The WEP key you use to transmit data must be set up exactly the same on your access point and any
wireless devices with which it associates. For example, if you set WEP Key 3 on your client adapter to wireless devices with which it associates. For example, if you set WEP Key 3 on your client adapter to
0987654321 and select i t as the transmit key 0987654321 and select i t as the transmit key, you must also set WEP Key 3 on the access point to exactly
the same value. The access point does not need to use Key 3 as its transmit key, however. the same value. The access point does not need to use Key 3 as its transmit key, however.
Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for instructions
on setting the access point's WEP keys. on setting the access point's WEP keys.
Wireless clients attempting to authenticate with your access point must support the same security options Wireless clients attempting to authenticate with your access point must support the same security options
configured in the access point, such as EAP or LEAP, MAC address authentication, Message Integrity configured in the access point, such as EAP or LEAP, MAC address authentication, Message Integrity
Check (MIC), WEP key hashing, and 802.1X protocol versions. Check (MIC), WEP key hashing, and 802.1X protocol versions.
Network Interfaces > Radio0-802.11B or or
and the radio status page displays.
tsunami . Refer to the
for instructions on how to configure an SSID.
) is not supported in access points running Cisco IOS Release 12.3(4)JA or
, you must also set WEP Key 3 on the access point to exactly
Checking Basic Settings Checking Basic Settings
in radio range, the client device will
. Refer to the Cisco IOS Software Configuration Cisco IOS Software Configuration
OL-8369-04 OL-8369-04
for instructions