Manually Configuring Controller Information Using The Access Point Cli - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04

Manually Configuring Controller Information Using the Access Point CLI

Manually Configuring Controller Information Using the Access Point CLI

T T a a b b l l e e 4 4 - - 2 2 U U s s i i n n g g C C L L I I P P o o w w e e r r C C o o m m m m a a n n d d s s
Power Source Power Source
A A C C p p o o w w e e r r m m o o d d u u l l e e
Cisco switch that supports Intelligent Power Cisco switch that supports Intelligent Power
1 1
Management Management
Cisco switch that does not support Intelligent Cisco switch that does not support Intelligent
Power Management Power Management
2 2
Power injector Power injector used with a Cisco switch that used with a Cisco switch that
supports Intelligent Power Management supports Intelligent Power Management
2 2
Power injector Power injector used with a Cisco switch that used with a Cisco switch that
does not support Intelligent Power does not support Intelligent Power
1 1
Management Management
P P o o w w e e r r i i n n j j e e c c t t o o r r u u s s e e d d w w i i t t h h a a n n o o n n - - C C i i s s c c o o s s w w i i t t c c h h
8 8 0 0 2 2 . . 3 3 a a f f c c o o m m p p l l i i a a n n t t n n o o n n - - C C i i s s c c o o s s w w i i t t c c h h e e s s
1. 1. You should check the rel You should check the release notes for your Cisc
for Intelligent Power Management might not be currently available for for Intelligent Power Management might not be currently available for your Cisco power source.
2. 2. Powe Power injecto r injector must be AIR-P r must be AIR-PWRINJ
3. 3. Cisco switch Cisco switches that suppo es that support Intelligent Po
Manually Configuring Controller Information Using the Access Manually Configuring Controller Information Using the Access
Point CLI Point CLI
Note Note
Refer to T Refer to T able able 4-2 for information on when to use these special CLI controller commands and the 4-2 for information on when to use these special CLI controller commands and the
corresponding Cisco switch power command. corresponding Cisco switch power command.
C C i i s s c c o o W W i i r r e e l l e e s s s s L L A A N N C C o o n n t t r r o o l l l l e e r r
N N o o n n e e r r e e q q u u i i r r e e d d
None required None required
c c o o n n f f i i g g a a p p p p o o w w e e r r p p r r e e - - s s t t a a n n d d a a r r d d e e n n a a b b l l e e
1 1
None required None required
1 1
c c o o n n f f i i g g a a p p p p o o w w e e r r i i n n j j e e c c t t o o r r e e n n a a b b l l e e
N N o o n n e e r r e e q q u u i i r r e e d d
N N o o n n e e r r e e q q u u i i r r e e d d
ease notes for your Cisco power source to determine whic o power source to determine which Cisco IOS release s
WRINJ3 or AIR-PW 3 or AIR-PWRINJ RINJ-FIB
rt Intelligent Power Management a wer Management always configure t
In a new installation, when your access point is unable to reach a DHCP server, you can manually In a new installation, when your access point is unable to reach a DHCP server, you can manually
configure needed controller information using the access point CLI. For information on how to connect configure needed controller information using the access point CLI. For information on how to connect
to the console port, see the "Connecti to the console port, see the
The CLI commands in this section can be used only on an access point that is not associated to a The CLI commands in this section can be used only on an access point that is not associated to a
controller. controller.
The static information configured with the CLI commands are used by the access point to connect with The static information configured with the CLI commands are used by the access point to connect with
a controller. After connecting with the controller, the controller reconfigures the access point with new a controller. After connecting with the controller, the controller reconfigures the access point with new
controller settings, but the static IP addresses for the access point and the default gateway are not controller settings, but the static IP addresses for the access point and the default gateway are not
changed. changed.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
h Cisco IOS release supports Intellige
your Cisco power source.
-FIB. .
lways configure the use of a powe he use of a power injector at the
"Connecting to the Access Point Console Port" sect ng to the Access Point Console Port"
Point Hardware Installation Guide
Chapter 4 4 Chapter Troubleshooting Lightweight Troubleshooting Lightweight Access
CLI Commands CLI Commands
C C i i s s c c o o S S w w i i t t c c h h
power inline never power inline never
power inline auto power inline auto
p p o o w w e e r r i i n n l l i i n n e e a a u u t t o o
power inline never power inline never
p p o o w w e e r r i i n n l l i i n n e e n n e e v v e e r r
– –
– –
upports Intelligent Power Management. Su nt Power Management. Support
r injector at the switch. switch.
section on page ion on page
4-7 4-7
Access Points Points
3 3
pport
4-12. . 4-12