Power Sources; Ul 2043 Certification - Cisco Aironet 1130AG Series Hardware Installation Manual

Chapter 1 Chapter 1 O Overview verview

Power Sources

Power Sources
Warning Warning
Caution Caution
Note Note

UL 2043 Certification

UL 2043 Certification
Caution Caution
OL-8369-04 OL-8369-04
The access point can receive power from an external power module or from inline power using the The access point can receive power from an external power module or from inline power using the
Ethernet cable. T he access point supports th Ethernet cable. T he access point supports th e IEEE 802.3af
Negotiatio Negot iation. Using inline power, you do no n. Using inline power, you do no t need to run a power cord
is supplied over the Ethernet cable. is supplied over the Ethernet cable.
This product must be connected to a Power over Ethernet (PoE) IEEE This product must be connected to
or an IEC60950 compliant limited power source. or an IEC60950 compliant limited power s
Be careful when handling the access point; the bottom plate might be hot. Be careful when handling the access point; the bottom plate might be hot.
The access point supports the following power sources: The access point supports the following power sources:
• • Power module Power module
• • Inline power: Inline power:
Cisco A Cisco Aironet Power ironet Power Injector
– –
An inline power capable switch, such as the Cisco Catalyst 3550 PWR XL, 3560-48PS, An inline power capable switch, such as the Cisco Catalyst 3550 PWR XL, 3560-48PS,
– –
3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module 3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module
Other inline power switches supporting the IEEE 802.3af inline power standard Other inline power switches supporting the IEEE 802.3af inline power standard
– –
Some switches and patch panels might not provide enough power to operate the access point when Some switches and patch panels might not provide enough power to operate the access point when
configured with both 2.4-GHz and 5-GHz rad configured with both 2.4-GHz and 5-GHz rad ios. At power-up, if the access point is unable to determine
that the power source can supply sufficient power, the access point automatically dea that the power source can supply sufficient power, the access point automatically dea ctivates both radios
to prevent an over-current condition. The access point also activates a Status LED low power error to prevent an over-current condition. The access point also activates a Status LED low power error
indication (refer to the "Low Power Condi indication (refer to the "Low Power
the "Low Power Condit the "Low Power Condition for Lightweight Access Points ion for Lightweight Access
The access point has adequate fire resistance and low smoke-producing characteristics suitable for The access point has adequate fire resistance and low smoke-producing characteristics suitable for
operation in a building's environmental air space, such as above suspended ceilings, in accordance with operation in a building's environmental air space, such as above suspended ceilings, in accordance with
Section 300-22(c) of the NEC, and with Sections 2-128, 12-010(3) and 12-100 of the Section 300-22(c) of the NEC, and with Sections 2-128, 12-010(3) and 12-100 of the Canadian
Electric Elec tric al C al C ode ode , Part 1, C22.1. , Part 1, C22.1.
Only the fiber-optic power injector (AIR-PWRINJ-FIB) has been tested to UL 2043 for operation in a Only the fiber-optic power injector (AIR-PWRINJ-FIB) has been tested to UL 2043 for operation in a
building's environmental air space; the AIR-PWRINJ3 power injector and the power module are not building's environmental air space; the AIR-PWRINJ3 power injector and the power module are not
tested to UL 2043 and should not be placed in a building's environmental air space, such as above tested to UL 2043 and should not be placed in a building's environmental air space, such as above
suspended ceilings. suspended ceilings.
e IEEE 802.3af inline power standard and
t need to run a power cord to the access point beca
a Power over Ethernet (PoE) IEEE 802.3af compliant power source
ource.
Statement 353 Statement 353
Injector (AIR- (AIR-PWRINJ PWRINJ3 or 3 or AIR-PW AIR-PWRINJ-F
ios. At power-up, if the access point is unable to determine
Condition for Autonomou tion for Autonomous Access Points" sect
Points" section on page
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
Hardware Features Hardware Features
inline power standard and Cisco
to the access point beca use power
802.3af compliant power source
RINJ-FIB) IB)
ctivates both radios
s Access Points" section on page ion on page
" section on page 4-6). ). 4-6
Point Hardware Installation Guide
Cisco CDP Po CDP Power wer
use power
3-6 or 3-6 or
Canadian
1-5 1-5