Dual-Radio Operation; Ethernet Port; Console Port; Leds - Cisco Aironet 1130AG Series Hardware Installation Manual

Hardware Features Hardware Features

Dual-Radio Operation

Dual-Radio Operation

Ethernet Port

Ethernet Port
Note Note

Console Port

Console Port
Note Note

LEDs

LEDs
Note Note
Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
1-4 1-4
The access point supports simultaneous radio operation using a 2.4-GHz 802.11g radio and a 5-GHz The access point supports simultaneous radio operation using a 2.4-GHz 802.11g radio and a 5-GHz
802.11a radio. Each radio uses dual-diversity integrated antennas. 802.11a radio. Each radio uses dual-diversity integrated antennas.
The 5-GHz radio incorporates an Unlicensed National Information Infrastructure (UNII) radio The 5-GHz radio incorporates an Unlicensed National Information Infrastructure (UNII) radio
transceiver operating in the UNII 5-GHz frequency bands. The 802.11g radio is called Radi transceiver operating in the UNII 5-GHz frequency bands. The 802.11g radio is called
802.11a radio is called Radi 802.11a radio is called Radio1
The auto-sensing Ethernet port accepts an RJ-45 connector, linking the access point to your 10BASE-T The auto-sensing Ethernet port accepts an RJ-45 connector, linking the access point to your 10BASE-T
or 100BASE-T Ethernet LAN. The access point can receive power through the Ethernet cable from a or 100BASE-T Ethernet LAN. The access point can receive power through the Ethernet cable from a
power injector, switch, or power patch panel. The Ethernet MAC address is printed on the label on the power injector, switch, or power patch panel. The Ethernet MAC address is printed on the label on the
back of the access point (refer to the "Locating the Produ back of the access point (refer to the
port is located in a cable bay area that is hidden by the closed top cover (see Fi Figur port is located in a cable bay area that is hidden by the closed top cover (see
Do not attempt to connect a cable with a protective boot to the access point Ethernet port. Because of Do not attempt to connect a cable with a protective boot to the access point Ethernet port. Because of
limited space in the connection area, booted connectors might not fit. limited space in the connection area, booted connectors might not fit.
The serial console port can be used to monitor the access point power-up sequences using a terminal The serial console port can be used to monitor the access point power-up sequences using a terminal
emulator program. The port is located in a cable bay area that is hidden by the top cover (see Fi Figu emulator program. The port is located in a cable bay area that is hidden by the top cover (see
Use an RJ-45 to DB-9 serial cable to connect your computer's COM port to the access point's serial Use an RJ-45 to DB-9 serial cable to connect your computer's COM port to the access point's serial
console port. (Refer to Appendix console port. (Refer to Appendix
pinouts.) Assign the following port settings to a terminal emulator to open the management system pinouts.) Assign the following port settings to a terminal emulator to open the management system
pages: 9600 baud, 8 data bits, No parity, 1 stop bit, and no flow control. pages: 9600 baud, 8 data bits, No parity, 1 stop bit, and no flow control.
Do not attempt to connect a cable with a protective boot to the access point console port. Because of Do not attempt to connect a cable with a protective boot to the access point console port. Because of
limited space in the connection area, booted connectors might not fit. limited space in the connection area, booted connectors might not fit.
The access point has three LEDs to indicate Ethernet activity, radio activity, and status indications (see The access point has three LEDs to indicate Ethernet activity, radio activity, and status indications (see
Figur ure Fig e 1- 1-1 1 ). For additional information, refer to the ). For additional information, refer to the "Troubleshooting Autonomous Access Points"
section on pag sect ion on page e 3-1 3-1 or the or the "Tro "Troubleshoot
• • The Status LED provides general operating status and error indications (top cover closed). The Status LED provides general operating status and error indications (top cover closed).
• • The Ethernet LED is loca The Ethernet LED is loca ted in the cable bay area under the
Ethernet traffic on the wired Ethernet LAN and provides Ethernet error indications. Ethernet traffic on the wired Ethernet LAN and provides Ethernet error indications.
• • The Radio LED is located in the cable bay area under the access point top cover. This LED signals The Radio LED is located in the cable bay area under the access point top cover. This LED signals
that wireless packets are being transmitted or received over the radio interface and provides radio that wireless packets are being transmitted or received over the radio interface and provides radio
error indications. error indications.
The access point cover must be closed to view the Status LED but the cover must be open to view the The access point cover must be closed to view the Status LED but the cover must be open to view the
Ethernet and the Radio LEDs. Ethernet and the Radio LEDs.
Hardware Installation Guide
o1 . .
"Locating the Product Serial Number" sect
E, "Console E, "Console Cab Cable Pinouts le Pinouts," ," for a description of the console port
"Troubleshooting Autonomous Access Points"
ubleshooting Lightweigh ing Lightweight Access Points" section on page
ted in the cable bay area under the access point top cover. This LED signals
Chapter er 1 1 Chapt
ct Serial Number" section on page ion on page
gure e
for a description of the console port
t Access Points" section on page
access point top cover. This LED signals
Overview Over view
Radio0 o0 and the and the
xvi). The xvi ). The
1- 1-1 1 ). ).
gure re 1- 1-1 1 ). ).
4-1. . 4-1
OL-8369-04 OL-8369-04