Cisco Aironet 1130AG Series Hardware Installation Manual page 123

Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
G-2 G-2
Appendix G G Appendix Configuring D Configurin
Configuring Option 43 for 1000 and 1500 Series Access Points Configuring Option 43 for 1000 and 1500 Series Access Points
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
Hardware Installation Guide
g DHCP HCP Option Option 43 43 for for Lightweigh Lightweight A t Access
To configure DHCP Option 43 for Cisco 1000 and 1500 se ries lightweight access points in the emb To configure DHCP Option 43 for Cisco 1000 and 1500 se
Cisco IOS DHCP server, follow these steps: Cisco IOS DHCP server, follow these steps:
Enter configuration mode at the Cisco IOS command line interface (CLI). Enter configuration mode at the Cisco IOS command line interface (CLI).
Create the DHCP pool, including the necessary parameters such as default router and name server. A Create the DHCP pool, including the necessary parameters such as default router and name server. A
DHCP scope example is as follows: DHCP scope example is as follows:
< < > >
ip dhcp pool ip dhcp pool pool name pool name
< < > < > <
network network IP Network IP Network Netmask Netmask
< <
default-router default-router Default router Default router
< < > >
dns-server dns-server
DNS Server DNS Server
Where: Where:
<pool name> is the name of the DHCP pool, such as AP1000 <pool name> is the name of the DHCP pool, such as AP1000
<IP Network> is the network IP address where the controller resides, such as 10.0.15.1 <IP Network> is the network IP address where the controller resides, such as 10.0.15.1
<Netmask> is the subnet mask, such as 255.255.255.0 <Netmask> is the subnet mask, such as 255.255.255.0
<Default router> is the IP address of the default router, such as 10.0.0.1 <Default router> is the IP address of the default router, such as 10.0.0.1
<DNS Server> is the IP address of the DNS server, such as 10.0.10.2 <DNS Server> is the IP address of the DNS server, such as 10.0.10.2
Add the option 60 line using the following syntax: Add the option 60 line using the following syntax:
option 60 ascii "Airespace.AP1200" option 60 ascii "Airespace.AP1200"
The quotation marks must be included. The quotation marks must be included.
Add the option 43 line using the following syntax: Add the option 43 line using the following syntax:
Comma Separated IP Address List Comma Separated IP Address List
option 43 ascii " option 43 ascii "
For example, if you are configuring option 43 for Cisco 1000 ser For example, if you are configuring option 43 for Cisco 1000 ser ies access points using the controller IP
addresses 10.126.126.2 and 10.127.127.2, add the following line to the DHCP pool in the Cisco IOS addresses 10.126.126.2 and 10.127.127.2, add the following line to the DHCP pool in the Cisco IOS
CLI: CLI:
option 43 ascii "10.126.126.2,10.127.127.2" option 43 ascii "10.126.126.2,10.127.127.2"
The quotation marks must be included. The quotation marks must be included.
ccess Points Points
Configuring Option 43 for 1000 and 1500 Series Access Points Configuring Option 43 for 1000 and 1500
> >
> >
ries lightweight access points in the emb edded
" "
ies access points using the controller IP
OL-8369-04 OL-8369-04
Series Access Points
edded