Table of Contents
Advertisement
AutoDome 700 Series IP PTZ Camera
4.
5.
6.
7.
8.
9.
10. Refer to Section 2.9 Attach Pendant to Arm and Tighten, page 28, to continue the VG5
NOTICE!
After all wiring is complete, close the cover door and tighten the two (2) captive screws on
the cover door to 10-12 N-m (90-105 in.-lbs) to ensure the Power Supply Box is watertight.
2.8
Installing the VG4-A-ARMPLATE
This section provides instructions to install a wall, corner, or mast mount with the VG4-A-
ARMPLATE Mounting Plate instead of a Power Supply Box.
CAUTION!
You must route the main power supply through a 120/230 VAC transformer (VG4-PSU1 or
VG4-PSU2 power supply box) before connecting the power to a 24 VAC AutoDome.
WARNING!
A stud diameter of 6.4 mm (1/4 inch) to 8 mm (5/16 inch) able to withstand a 120 kg (265 lb)
pull-out force is recommended. The mounting material must be able to withstand this pull out
force. For example, 19-mm (3/4-inch) minimum for plywood.
1.
2.
Bosch Security Systems, Inc.
Connect the 5-pin, 24 VAC to Dome Plug from the Pendant Connector Harness to its
corresponding color mating connector P107 on the right side of the box.
To connect alarm inputs and relay outputs, connect the 4-pin Alarms Out, the 6-pin
Alarms In and the 7-pin Relay connectors from the Pendant Connector Harness to their
mating connectors, installed previously, to the incoming alarm wires.
Connect the 3-pin Power In Plug, installed previously, to its matting connector P101 on
the left side of the box.
Connect the incoming RJ45 video connector, installed previously, to its mating connector
from the Pendant Connector Harness. Refer to Section 5 Cable and Wire Standards,
page 57 for connections and specifications.
Attach the grounding strap of the Pendant Arm to the Power Supply Box. Refer to .
After making the harness connections to the Power Supply Box, rotate the Pendant Arm
to close and seal the Power Supply Box and tighten the two (2) captive screws to
10-12 N-m (90-105 in.-lbs).
AutoDome Installation procedure.
For a Corner installation:
a.
Secure the Corner Plate to the wall corner using four (4) studs (not included).
b.
Secure the Mounting Plate to the Corner Plate using the four (4) 3/8 x 1-3/4-inch
bolts and split lock washers (supplied).
For a Mast or pole installation:
The metal straps included with the Mast mount accommodate a pole with a diameter of
100–380 mm (4–15 in.). You must use a banding tool (sold separately) for a mast or pole
installation. In addition, you must obtain a 3/4 in. (20-mm) right angle conduit connector
through which you route the wires that connect to the pendent arm.
a.
Follow the instructions provided with the banding tool to securely mount the Mast
Plate to the pole. Contact your Bosch Sales Representative to order Banding Tool
P/N TC9311PM3T.
b.
Secure the Mounting Plate to the Mast Plate using the four (4) 3/8 x 1-3/4-inch bolts
and split lock washers (supplied).
c.
Remove one of the rubber gaskets from the Mounting Plate.
Installation Manual
Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en
23
F.01U.215.779 | 1.0 | 2011.07
Advertisement
Table of Contents
