Selecting The Settings And Functions - Kyocera KM-6330 Operation Manual

24 If there are no problems with the copy set you made, then
you can use the repeat copy mode to make any additional
number of copy sets as desired (see "(2) Printing out with the
repeat copy mode" on page 5-44).

(2) Selecting the settings and functions

1 Selecting the paper
This procedure selects the size of the copy paper.
1 With the content of the "Basic" tab displayed, touch the
"Select paper" key. The "Select paper" screen will be
displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
1-sided
11x8 1 / "
2
Select Original
paper
type
None AMS
Reduce
Finished
/Enlarge
Basic Quality
Metric specifications
Ready to Job build.
Set original. Press Start key.
Job Build -Step 1
1-sided
Select
Original
paper
type
None AMS
Reduce/
Finished
Enlarge
Basic Quality
2 Touch the key that corresponds to the drawer[cassette]
which contains the desired size of copy paper, and then
touch the "Close" key. The touch panel will return to the
screen in step 1.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Select paper
11x8 1 / "
2
Plain
11x8 1 / "
2
Color
11x8 / "
1
2
Plain
Metric specifications
Ready to Job build.
Set original. Press Start key.
Select paper
Plain
Colour
Plain
1 sided copy
1 sided/
2 sided
1 sided copy-Left
Back Edge
Finished page #:0
Orig. set
direction
Edit
1-sided Copy
1-sided/
2-sided
1-sided Copy-Left
Back Edge
Finished page #: 0
Orig. set
direction
Edit
Back
Bypass
Plain
11x8 / "
1
2
Plain
Back
Bypass
Plain
Plain
Section 5 OTHER CONVENIENT FUNCTIONS
2 Specifying the type of originals
This procedure specifies the type of originals being copied between
1-sided, 2-sided and open-faced.
1 With the content of the "Basic" tab displayed, touch the
"Original type" key. The "Original type" screen will be
displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
Select
paper
None
Finished
Set
End
Metric specifications
Insert
page
Ready to Job build.
Set original. Press Start key.
Job Build
Select
paper
None
Finished
Set
End
2 Select between "1 sided", "2 sided" and "Book", in
Insert
blank page
accordance with the originals being copied.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Original type
1 sided
2 sided
Book
Set
Metric specifications
Close
Ready to Job build.
Set original. Press Start key.
Original type
1 sided
2-sided
Book
Set
NOTES
Close
• If you selected "1 sided", verify the direction in which the originals
were set.
• If you selected "2 sided", specify the binding direction of the
originals and then verify the direction in which the originals were
set.
• If you selected "Book", specify the binding direction of the
originals.
3 Touch the "Close" key. The touch panel will return to the
screen in step 1.
1-sided 1 sided copy
11x8 1 / "
2
Original
1 sided/
type 2 sided
1 sided copy-Left
AMS Back Edge
Finished page #:0
Reduce Orig. set
direction
/Enlarge
Basic Quality Edit
-Step 1
1-sided 1-sided Copy
Original
1-sided/
type
2-sided
1-sided Copy-Left
Back Edge
AMS
Finished page #: 0
Reduce/ Orig. set
Enlarge
direction
Basic Quality Edit
Set
End
Insert
page
Set
End
Insert
blank page
Set
Back Close
Check direction
Check direction of
original top side.
Left top
Rear
corner
Set
Back Close
Check direction
Check direction of original.
Left top
Back Edge
corner
5-63