Dealer Code - NAPCO GEMINI GEM-P1632 Programming Instructions Manual

WI1148B 10/06
KEYFOB ZONE ASSIGNMENT: Keyfobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the
keyfob, the location where the person holding the keyfob is stationed, or the special purpose of the keyfob button being depressed.
See Keyfob Transmitters as Zone Input Devices .
KFob0 1
Area
(Direct Entry)
00000 0
(Direct Entry)
:0 0 0
(Direct Entry)
, respectively; "A" =
9
.
G 3
If the Keyfob is converted for Two Button "Emergency Use" (by cutting an internal jumper), both top
or bottom buttons must be depressed to activate an alarm. In this case, the Aux-1 and Aux-2 cannot
U
be programmed. Press
report openings and closings as Users 25-32.
Keyfob Transmitters as Zone Input Devices
(refer to display as shown above: press the PRIOR/NO button to go backwards).
Each of the 4 keyfob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point 3; A2 =
point 4. Up to 32 keyfobs (using 1 button) or 16 keyfobs (using 2 buttons) or 8 keyfobs (using all 4 buttons) or any combination up to
a maximum of 32 controlled zones can be assigned, providing multiple wireless panic buttons on a system, each reporting to a
Central Station or a pager and/or annunciating on a keypad the keyfob zone number with description/location. To assign a keyfob to
a zone: program the keyfob as you would a transmitter, entering the keyfob's ID code, check sum and point number at the
appropriate zone. The "Quick Method" is not allowed. The zone may be hardwired to an electrical sensor as well as assigned to a
keyfob (either one will activate the zone alarm output). NOTE: If assigning a keyfob to a zone, the "ON/OFF" buttons on the keyfob
will no longer arm/disarm the system. The keyfob is converted to a "panic only" device.
ZONE DESCRIPTIONS: GEM-RP2ASe2 cannot be used to enter Zone Descriptions. To enter Zone Descriptions, you must use the
GEM-RP1CAe2 Keypad / GEM-K1CA Keypad (See WI897) or the Napco PCD-Windows Quickloader Software.
D Cod e
(Direct Entry)
45678 9
(Direct Entry)
RE-ENT
(Direct Entry)
L
NAPCO Security Systems
Keyfob Transmitters as Arm/Disarm & Control Devices
(Press to set cursor).
R
Keyfobs can be programmed as "Arm/Disarm" devices using their On/Off buttons (refer to WI752). For
each Keyfob Transmitter, enter:
The Keyfob Transmitter number (01–08). Press
Area number to which transmitter is assigned (0 to disable keyfob, 1 or 2). Press
and for 0, 1 and 2, respectively.
2
The 6-digit RF ID # printed on the transmitter (enter all numbers and/or letters, including leading
"0"s, if any): "0" through "9" =
; "D" =
G 2 G 3
1-digit checksum number printed on the transmitter.
Aux 1 Option (see keyfob aux 1 & aux 2 options).
Aux 2 Option (see keyfob aux 1 & aux 2 options).
For Aux 1/Aux 2 Options: "0", "1", "2" and "9" =
; "B" =
G 0 G 1
to save. Press the NEXT/YES button to proceed.

Dealer Code

Directly enter the Dealer Code (default = 456789), including leading zeros. Use the
buttons. NOTE: Press
9
U
the previous code. Press
01
through ; "A" =
0 9
; "E" = and "F" =
G 4
,
0 1
; "C" =
G 2
NOTE: Keyfobs 1-8
for a zero. Press
0
to save. Press the NEXT/YES button to proceed.
X
through
0 8
; "B" =
G 0 G 1
.
G 5
DATA
ENTRY
0
1
, and
2
2
and "D" =
9
A
B
C
D Access on PGM2 Output
E
F
U
to save. Re-enter the Dealer Code to verify
GEM-P1632 Programming Instructions
Page 11
for 01-08.
,
0 1
; "C" =
AUX 1/AUX 2
OPTIONS
None
Relay Group 1 Toggle
Relay Group 2 Toggle
Keypad Panic
Keypad Aux.
Instant
PGM2 Ouput Toggle
Arm Stay
Interior Button
through
1