Table of Contents
Advertisement
f
SMX 44 FOX 4G MM — Connect fiber optic input cables from a signal
source to the port marked "Inputs" and from the port marked "Outputs" to a
suitable display. LEDs light when signals are present.
1
2
IN
IN
OUT
OUT
FIBER OPTIC
g
SMX 88 SDI — Connect SDI, HD-SDI or dual link HD-SDI input signals to
any of the BNC input connectors. Connect suitable display devices to the
BNC output connectors.
1
2
3
4
5
SDI / HDSDI INPUTS
h
SMX 88 VGA — Connect high resolution computer-video rate input signals
to any of the 15-pin HD female connectors. Connect suitable display devices
to the 15-pin HD output connectors.
COMPUTER IN
4
1
2
3
5
6
7
8
i
SMX 88 SV (DIN) and
any of the BNC pairs or 4-pin mini DIN input connectors. Connect suitable
display devices to the BNC pairs or 4-pin mini DIN output connectors.
1
2
3
4
5
6
S-VIDEO IN
1
2
4
1
2
3
S-VIDEO IN
k
SMX 84 V — Connect composite video input signals to the BNC input
connectors. Connect display devices to the BNC output connectors.
1
2
3
4
5
6
VIDEO INPUTS
l
SMX 88 A — Connect stereo or mono audio input signals to any of the eight
sets of 3.5 mm, 5-pole captive screw connectors marked Inputs. Wire the
connector for the appropriate signal type,
INPUTS
1
2
3
4
5
6
L
R
L
R
L
R
L
R
L
R
L
R
Connect audio devices, such as an audio amplifier or powered speakers to the
eight sets of 3.5 mm, 5-pole captive screw connectors marked Outputs. The
connectors output the selected unamplified, line level audio.
properly wire an output
By default, audio and video use different boards, so that audio breakaway is
switched separately. This is done via the front panel, Ethernet, or the RS-232
link, allowing selection from any of the audio input sources. See
"Operation and
Setup",
Control
Software", and
m
Plane address rotary switch — This 16 position rotary switch allows the
user to plane address up to sixteen I/O boards. To set an
address, insert a small screwdriver in the slot and rotate to
the desired number (0-9, A-F). Each plane address is then
identifiable during SMX control and configuration.
SMX System MultiMatrix Switchers • Installation
3
4
5
IN
IN
IN
OUT
OUT
OUT
ADDRESS
DIGITAL VIDEO
6
7
8
1
1
2
2
ADDRESS
1
5
ADDRESS
j
SMX 84 YC — Connect S-video input signals to
S-VIDEO
7
8
1
2
3
ADDRESS
S-VIDEO
4
3
1
2
3
ADDRESS
S-VIDEO OUT
VIDEO
7
8
1
2
3
ADDRESS
VIDEO OUTPUTS
as shown on page 2-8.
7
8
1
2
3
L
R
L
R
L
R
L
R
L
R
L
ADDRESS
connector.
chapter 4, "Programmers
chapter 6, "HTML
Operation", for details.
6
7
8
IN
IN
IN
OUT
OUT
OUT
FIBER OPTIC
3
3
4
4
5
5
6
6
7
7
8
8
SDI / HDSDI OUTPUTS
COMPUTER OUT
4
2
3
6
7
8
i
4
5
6
7
8
S-VIDEO OUT
j
4
4
OUTPUTS
4
5
6
7
8
R
L
R
L
R
L
R
L
R
See page 2-8 to
chapter 3,
Guide",
chapter 5, "SMX
ADDRESS
2-7
Advertisement
Table of Contents
