Table of Contents
Advertisement
KX-FP320G / KX-FM330G
2.4.4.
SERVICE FUNCTION TABLE
Code
501
Pause time set
502
Flash time set
503
Dial speed select
511
VOX sense
520
CED frequency select
521
International mode select
522
Auto standby select
523
Receive equalizer select
524
Transmission egualizer select
546
Flash time (CO)
550
Memory clear: To reset the value to the default one, except the top margin (853)and left
margin (854).
551
ROM check
552
DTMF single tone test
553
Monitor on FAX communication
select
554
Modem test
555
Scan check
556
Motor test
557
LED test
558
LCD test
559
Paper jam detection select
561
KEY test
570
BREAK % select
571
ITS auto redial time set
572
ITS auto redial line disconnection
time set
573
Remote turn-on ring number set
580
TAM continuous tone detection
590
FAX auto redial time set
591
FAX auto redial time disconnection
time set
592
CNG transmit select
593
Time between CED and 300bps
594
Overseas DIS detection select
Function
Set Value
X 100 ms.
X 10 ms.
1:10 pps 2:20 pps
1:High 2:Low
1:2100 Hz 2:1100 Hz
1:ON 2:OFF
1:ON 2:OFF
1:0km 2:1.8km
3:3.6km 4:7.2km
1:0km 2:1.8km
3:3.6km 4:7.2km
X 10 ms.
1:ON 2:OFF
1: OFF 2:PHASE B
3:ALL phases
1:ON 2:OFF
1:61% 2:67%
X number of times
X second
X number of rings
1:ON 2:OFF
X number of times
X second
1:OFF 2:ALL 3:AUTO
1: 75 ms. 2:500 ms.
3:1 sec
1:detects at the 1st
time 2:detects at the
2nd time
Effective Range
Default
001~600
030
01~99
08
1, 2
1
1, 2
1
1, 2
1
1, 2
2
1, 2
1
1~4
1
1~4
1
01~99
20
1, 2
2
1~3
1
00
1, 2
1
1, 2
1
00~99
11
001~999
060
01~99
10
1, 2
1
00~99
11
001~999
060
1~3
2
1~3
1
1, 2
1
104
Remarks
See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
The resolution reverts to the
default when transmission is
complete.
When the telephone station is far
from the unit or reception cannot
be performed correctly, adjust
accordingly.
When the telephone station is far
from the unit or transmission
cannot be performed correctly,
adjust accordingly.
"START" input.
"START" input.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.2.1. Paper Jam.
See 2.5. TEST FUNCTIONS.
Sets the % break of pulse dialing
according PBX.
Selects the number of times that
ITS is redialed (not including the
first dial).
Sets the interval of ITS redialing.
Sets the number of rings before
the unit starts to receive a
document in the TEL mode.
ON: STOP TAM operation when
Dial tone, etc. are detected.
Selects the number of redial times
during FAX communication (not
including the first dial).
Sets the FAX redial interval during
FAX communication.
Lets you select the CNG output
during FAX transmission. ALL:
CNG is output at phase A. AUTO:
CNG is output only when automatic
dialing is performed. OFF: CNG is
not output at phase A.
See the Symptom/Countermeasure
Table for long distance and
international calls in 2.3.3.3.1.
Defective facsimile section.
See the Symptom/Countermeasure
Table for long distance and
international calls in 2.3.3.3.1.
Defective facsimile section.
Advertisement
Table of Contents
Troubleshooting
