Kurzweil PC4 SE Musician's Manual page 121

Controller Controller
Number Destination
146 TransDown
147 Arp On/Off
148 CC Seq On/Off
149 Mute Zone
150 ArpOrder
151 ArpBeats
152 ArpShift
153 ArpLimit
154 ArpLmtOp
155 ArpVel
156 Arp Dur
157 Latch Sustain
158 Latch2:Sost
160 SusLatch
161 Panic
162 SoloZn
163 Riff OnOff
165 Riff Duration
166 Riff Velocity
167 Riff Delay
168 TapTempo
170 -ArpShift
171 ShiftPatt
172 ShiftPBank
Transpose Down (ST)
Values 0-63 turn the Arpeggiator Off, Values 64-127 turn the Arpeggiator On
Values 0-63 turn the CC Sequencer Off, Values 64-127 turn the CC Sequencer On.
Mute Zone – Values above 64 will mute the zone that sends values to this
destination, values below or equal to 64 will unmute the zone.
Arpeggiator PlayOrder, each range of values selects one of nine settings in order of
the parameter list: 0-14, 15-28, 29-42, 43-56, 57-70,71-84, 85-98, 99-112, 113-127.
(See
Play Order on page 3-20)
Values from 0-127 change the Arpeggiator Beats value (see
details).
The 88 Arpeggiator Shift steps are scaled over the 128 MIDI controller values, so
that 0 = 0 steps and 127 = 88 steps. (See
The 60 Arpeggiator Shift Limit steps are scaled over the 128 MIDI controller values,
so that 0 = 0 steps and 127 = 60 steps. (See
Arpeggiator Shift Limit Option, each range of values selects one of seven options in
order of parameters list: 0-18, 19-36, 37-54, 55-72, 73-90, 91-108, 109-127. (See
Limit Option on page 3-16)
Arpeggiator Velocity Mode, each range of values selects one of twenty-three op-
tions in order of parameters list: 0-5, 6-10, 11-15...101-105, 106-110, 111-127. (See
Velocity on page 3-20).
The Arpeggiator Duration % values are scaled over the 128 MIDI controller values,
so that 0 = 1% and 127 = 100%. (See
To control the Arpeggiator Latch switch, 0-63 = off, 64-127 = on. (See
3-14)
To control the Arpeggiator Latch2 switch, 0-63 = off, 64-127 = on.
For Arpeggiator Latch Pedals mode, 0-63 = off, 64-127 = on.
Sends an "all notes off" message and an "reset all controllers" message on all 16
MIDI channels.
Solo Zone - Values above 64 will solo the zone that sends values to this destination,
values below or equal to 64 will unsolo the zone. When soloing a Zone, all other
Zones will become muted, and unmuting a muted Zone will make that Zone the
soloed zone. If the currently soloed Zone has a controller assigned to Destination
149 (Mute Zone), solo mode can be canceled by sending a value to this destination.
If Riff is set to On on the Riff page, values 64-127 will trigger the riff, values 0-63 will
release the riff.
Controls the Riff Duration parameter. The Duration value is calculated by multiplying
the received controller value by 1000, and dividing the answer by 128 (any decimal
points are taken off the final value.) Here are some example values: 7 = 54%, 13 =
101%,19 = 148%, 32 = 250%, 64 = 500%, 127 = 992%
Controls the Riff Velocity parameter. The Velocity value is calculated by multiply-
ing the received controller value by 2. For Example, 25 = 50%, 50 = 100%, 100 =
200%, 127 = 254%.
Controls the Riff Offset parameter. Controller value 64 = 0 offset ticks. Each value
away from 64 = 512 offset ticks. For example, 63 = -512 offset ticks, 65 = +512
offset ticks, 0 = -32768 offset ticks, 127 = +32256 offset ticks.
Assign this to a switch (set to Type: Toggled) to control the tap tempo function, then
tap the switch in time to set the Multi tempo.
Sets Arpeggiator values for Shift to negative. 0-63 = off, 64-127 = on. (See
Amount on page 3-18)
Selects one of the 128 patterns in the current Arpeggiator Shift Pattern Bank. (See
Shift Pattern on page 3-18)
A controller value selects the corresponding Shift Pattern Bank for the Arpeggiator
page of a controller's zone. For example, controller value 2 selects Shift Pattern
bank 2, controller value 7 selects Shift Pattern bank 7.
Multi Edit Mode
Controls Page
Description
Beats on page 3-17
Shift Amount on page 3-18
Shift Limit on page 3-18)
Duration on page 3-24)
for
for details).
Latch on page
Shift
5-33