Preparation For Use - 3M 6000 Series Manual

use of these respiratory protection products and/or
failure to properly wear the complete product during
all periods of exposure may adversely affect the
wearer's health, lead to severe or life threatening
illness or permanent disability.
• For suitability and proper use follow local regulations,
refer to all information supplied or contact an
occupational hygienist, safety professional or 3M
representative on the Tech Assist Helpline 3M Australia
1800 024 464, 3M New Zealand 0800 364 357.
• Use this respirator strictly in accordance with all
instructions:
• - contained in this booklet,
• - accompanying other components of the system. (e.g.
3M™ Filters / 3M™ Air supply unit). See all instructions
for use and save for continuing reference.
• Do not use in concentrations above those specified in
Technical Specification.
• Do not use for respiratory protection against atmospheric
contaminants/concentrations which have poor warning
properties or are unknown or immediately dangerous to
life and health (IDLH) or against
contaminants/concentrations which generate high heats
of reaction with chemical filters.
• Do not use in atmospheres containing less than 19.5%
oxygen. (3M definition. Individual countries may apply
their own limits on oxygen deficiency. Seek advice if in
doubt).
• Do not use these products in oxygen or oxygen-enriched
atmospheres.
• Only use with the Filters/Air Supply Units and
Spares/Accessories listed in the Reference Leaflet and
within the usage conditions given in the Technical
Specification.
• Only for use by trained competent personnel.
• Leave the contaminated area immediately if:
a) Any part of the system becomes damaged.
b) Airflow to the face piece decreases or stops.
c) Breathing becomes difficult or increased breathing
resistance occurs.
d) Dizziness or other distress occurs.
e) You smell or taste contaminants or irritation occurs.
• Never modify or alter this product. Replace parts only
with original 3M spare parts.
• In case of intended use in explosive atmospheres,
contact 3M Technical Service.
• Do not use these products with self-contained breathing
apparatus.
• Do not use for escape purposes.
• Do not use with beards or other facial hair that may
inhibit contact between the face and the product
thus preventing a good seal.
• Only use with the spectacle kit available as an accessory
with this product, and ensure spectacle arms do not
interfere with the faceseal.
• National regulations may impose specific limitations on
the use of filters depending on the filter class and the
facepiece used. Use of any 3M™ Face piece / Filter
combination should be in accordance with applicable
Health and Safety standards, AS/NZS 1715, Respiratory
Selection Tables or in accordance with the
recommendations of an Occupational Hygienist.
• Filters need to be regularly changed. The frequency of
change depends on usage time and the concentration of
contaminant.
• For more information call the 3M Tech Assist Helpline 3M
Australia 1800 024 464, 3M New Zealand 0800 364 357.
• If using with a 3M™ Air Supply Unit:
• At very high work rates, the pressure in the face piece
may become negative at peak inhalation flow. Adjust
equipment as appropriate or consider an alternative form
of respiratory protective device.
• If using in Supplied Air mode, ensure that: • The source
of the air supply is known. • The purity of the air supply is
known. • The air supply is of a breathable quality to
AS/NZS 1715.
If during use the air supply stops or is reduced, vacate the
contaminated area immediately and investigate the cause.
• Take care to prevent the breathing tube from becoming
looped around protruding objects
• These products do not supply oxygen.
NOTES REGARDING ALLERGIC REACTIONS
Materials which may come into contact with the wearer's skin
are not known to cause allergic reactions to the majority of
individuals.
These products do not contain components made from natural
rubber latex.

PREPARATION FOR USE

Inspect the package contents for shipping damage and ensure
all components are present.
Check apparatus is complete, undamaged and correctly
assembled. Any damaged or defective parts must be replaced
with original 3M spare parts before use.
Inspection
The following inspection procedure is recommended before
use:
1. Check the face piece for cracks, tears and dirt. Be certain
the face piece, especially the face seal area, is not distorted.
The material must be pliable – not stiff.
2. Examine the inhalation valves for cracks or tears. Lift valves
and inspect valve seat for dirt or cracks.
3. Ensure that the head straps are intact and have good
elasticity.
4. Examine all plastic parts for signs of cracks or fatigue.
5. Make sure all gaskets are properly seated.
6. Remove the exhalation valve cover and examine the
exhalation valve and valve seat for signs of dirt, distortion,
cracks or tears. Replace the exhalation valve cover.
7. Inspect lens for any damage that may impair respirator
performance or vision.
ASSEMBLY INSTRUCTIONS
See appropriate user instructions for assembly instructions.
(e.g. 3M™ Filters / 3M™ Air supply unit).
FITTING INSTRUCTIONS
Select most appropriate size from the 3 sizes of the face piece
available (S / M / L). Fitting Instructions must be followed each
time the product is worn.
111