Adjustment; 调整 - Kenwood NX-200 Service Manual

Controls
Selector
选择器
Orange key
橙色键
Panel Test Mode
■ Test mode operation features
This transceiver has a test mode. To enter test mode,
press and hold the [ ] key while turning the transceiver
power ON. Before the transceiver enters test mode, the
frequency version information appears on the LCD mo-
mentarily. Test mode can be inhibited by programming. To
exit test mode, turn the transceiver power OFF. The follow-
ing functions are available in test mode.
■ Key operation
"FNC" not appears on the sub LCD display
Key
Function
[Selector] -
Push: Test channel up
[ ] Hold: Test channel up
continuously
Push: Test channel down
[ ] Hold: Test channel down
continuously
Push: Squelch level up
[Side1]
Hold: Squelch off
[Side2] Wide/Narrow/Very narrow
[ ] Shift to panel tuning mode -
[ ] Function on
[ ] MSK 1200bps and 2400bps 2400bps:
Push: Test signaling up
[ ] Hold: Test signaling up
continuously
[Orange] -
[PTT] Transmit
Use as the DTMF keypad.
[0] to [9] If a key is pressed during
and transmission, the DTMF
[#], [ ] corresponding to the key
that was presses is sent.

ADJUSTMENT /

Power switch / Volume
电源开关/音量
PTT switch / PTT开关
Side1 key / Side1键
Side2 key / Side2键
Display
-
Channel No.
Channel No.
Squelch level
Squelch off: icon appears
Wide: "w"
Narrow: "n"
Very narrow: "v"
"FNC" appears on the
sub LCD display
icon appears
Signaling No.
-
-
-
调整
控制器
Universal connector
通用连接器
面板测试模式
■测试模式操作功能
本手持对讲机有测试模式。要进入测试模式，打开手持对
讲机电源时，按住 [ ] 键。手持对讲机进入测试模式之前，
LCD 上短时间出现频率版本信息。可以通过编程禁用测试模
式。如需退出测试模式，请关闭手持对讲机电源。在测试模
式可以使用下列功能。
■键操作
副 LCD 显示上不出现"FNC"
键
功 能
[ 选择器 ] -
按下 : 测试信道递增
[ ]
按住 : 测试信道持续递增
按下 : 测试信道递减
[ ]
按住 : 测试信道持续递减
按下 : 静噪电平递增
[Side1]
按住 : 静噪关
[Side2] 宽 / 窄 / 超窄
[ ] 换到面板调谐模式
[ ] 功能开
[ ] MSK 1200bps 和 2400bps
按下 : 测试信令递增
[ ]
按住 : 测试信令持续递增
[ 橙色 ] -
[PTT] 发射
用作 DTMF 键盘。如果在
[0] 至
发射时按下某个键，则
[9] 和
发送与按下的键对应的
[#]，[ ]
DTMF。
NX-200
显 示
-
信道号
信道号
静噪电平
静噪关。 图标出现
宽 :"w"
窄 :"n"
超窄 :"v"
-
副 LCD 显示上出现"FNC"
2400bps: 图标出现
信令号
-
-
-
67