Kenwood NX-200 Service Manual page 8

NX-200
Note:
This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
ware.
6-4. Function
1. If you press the [Side2] key while "PROGRAM 115200"
is displayed, the display changes to "PROGRAM 19200"
(The LED blinks green) to indicate that the write speed
is low speed (19200 bps). If you press the [Side2] key
again while "PROGRAM 19200" is displayed, the dis-
play changes to "PROGRAM 38400" (The LED lights
red and orange alternatively). If you press the [Side2]
key again while "PROGRAM 38400" is displayed, the
display changes to "PROGRAM 57600" (The LED blinks
orange). If you press the [Side2] key again while "PRO-
GRAM 57600" is displayed, the display returns to "PRO-
GRAM 115200" (The LED lights orange).
2. If you press the [Side1] key while "PROGRAM 115200"
is displayed, the checksum is calculated, and a result is
displayed. If you press the [Side1] key again while the
checksum is displayed, "PROGRAM 115200" is redis-
played.
Note:
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one trans-
ceiver to another by connecting them via their external uni-
versal connectors. The operation is as follows (the transmit
transceiver is the source and the receive transceiver is a
target).
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
Note:
The following data can be cloned.
• Fleet (own)/ID (own) for FleetSync
• Unit ID (own) for NXDN
Key guide on the Read authorization password input screen.
• CONFRM ([ ] key): The password confi rmation
• DELETE ([ ] key): Delete the least digit from the current
password number (Press and hold to delete all password
numbers)
• SELECT ([ ] key): Determine the least digit of the pass-
word number
1. Press and hold the [ ] key while turning the transceiver
power ON. If the Read authorization password is set to
the transceiver, the transceiver displays "CLONE LOCK".
If the password is not set, the transceiver displays
"CLONE MODE".
8
REALIGNMENT /
模式组合
注意 :
如果手持对讲机的固件编程模式设为禁用，则无法进入此
模式。
6-4. 功能
1. 如果在显示"PROGRAM 115200"时按 [Side2] 键，则显示
变为"PROGRAM 19200"(LED 呈绿色闪烁 )，表示写入速度
为低速 (19200bps)。如果在显示"PROGRAM 19200"时再
次按 [Side2] 键，则显示变为"PROGRAM 38400"(LED 呈红
色和橙色交替点亮 )。如果在显示"PROGRAM 38400"时再
次按 [Side2] 键，则显示变为"PROGRAM 57600"(LED 呈
橙色闪烁 )。 如果在显示 "PROGRAM 57600" 时再次按 [Side2]
键，则显示返至"PROGRAM 115200"(LED 呈橙色点亮 )。
2. 如果在显示"PROGRAM 115200"时按 [Side1] 键，则计算
校验和并显示结果。如果在显示校验和时再次按 [ S i d e1]
键，则重新显示"PROGRAM 115200" 。
注意 :
通常以高速模式写入。
7. 复制模式
用外部通用连接器连接手持对讲机，可以将编程数据从一
台手持对讲机传输到另一台手持对讲机。具体操作如下 ( 发
射机是主机，接收机是子机 )。
不能复制以下数据。
· 调谐数据
· 带密码的嵌入信息
• 机型数据
• ESN( 电子序列号 ) 数据
注意 :
可以复制以下数据。
• FleetSync 的 Fleet( 自身 )/ID( 自身 )
• NXDN 的 Unit ID( 自身 )
读取授权密码输入画面的按键说明。
• CONFRM([ ] 键 ): 密码确认
• DELETE([ ] 键 ): 删除当前密码数字的最低位数字 ( 按住
可删除全部密码数字 )
• SELECT([ ] 键 ): 确定密码数字的最低位数字
1. 打开手持对讲机电源时，按住 [ ] 键。如果手持对讲机设
置了读取授权密码，则手持对讲机会显示 "CLONE LOCK" 。
如果没有设置密码，则手持对讲机显示"CLONE MODE" 。