Changing The Insert Location Of The Insert Effect - Zoom HD16 Operation Manual

Reference [Effects]
instantly switch insert effect settings simply by selecting the
appropriate algorithm, and then selecting a patch.
The table below shows the number of patches for each
algorithm.
Algorithm Patches
CLEAN 30 (22)
DISTORTION 50 (40)
ACO/BASS SIM 20 (10)
BASS 30 (20)
MIC 50 (30)
DUAL MIC 50 (30)
LINE 50 (30)
8x COMP EQ
20 (10)
<< only>>
MASTERING 30 (21)
Changing the insert location of
the insert effect
In the default condition of a project, the insert effect is applied
to the input mixer. However, you may change the insert
location as necessary. The following possibilities are available.
Display
Input Input mixer
Drum Drum track output
Bass Bass track output
Track1, Track2... Any output of a mono track
Any output of a stereo track or
Track1/2, Track3/4...
mono track x 2
Master Immediately before [MASTER] fader
<< only>>
In addition to the above possibility, the HD16 offers the
following choices.
Display
Input1 – Input8 Any input of input mixer
Input1-8 All inputs of input mixer
Track1-8 All outputs of tracks 1 – 8
Track9-16 All outputs of tracks 9 – 16
NOTE
<< only>>
• Individual selection of Input 1 – Input 8 is possible only when the
8-track recording function is enabled and an algorithm other
than 8x COMP EQ is selected.
• Track 1 – 8 and Track 9 – 16 are only available when the 8x
COMP EQ algorithm is selected.
• Simultaneous selection of Input 1 – 8 is possible only when the
8-track recording function is enabled and the 8x COMP EQ
algorithm is selected.
• If you switch to the 8x COMP EQ algorithm after selecting the
insert position, the position will change to Input 1 – 8, Track 1 – 8,
128
(preprogrammed patches)
Insert position
Insert position
or Track 9 – 16 (depending on the immediately preceding setting).
Insertion to input
1.
On the main screen, verify that the [ON/OFF]
key for the desired input is lit in red. Then
press the [INPUT SOURCE] key in the control
section.
The current insert position is shown on the display.
Input Source Input Source
Input Input
2.
Verify that "Input" is selected.
If another position is selected, turn the dial to select "Input".
You can also make the selection by pressing an [ON/OFF] key
in the input section.
When the input is selected as insert position, all [ON/OFF]
keys are lit in orange. In this condition, the effect will apply to
one or two inputs as selected in step 1.
NOTE
<< only>> If the 8-track recording function is inactive,
you cannot select "Input" as insert position, even when the 8x
COMP EQ algorithm was selected.
3.
Press the [EXIT] key to return to the main
screen.
<< only>> Insertion to 8 input channels
With the HD16, when the 8-track recording function is enabled
and the 8x COMP EQ algorithm is selected, the insert effect
can be applied to 8 channels simultaneously.
1.
Press the [8TRACK RECORDING] key in the
input section so that the [ON/OFF] keys for
inputs 1 – 8 are lit in red.
2.
Select 8x COMP EQ as algorithm for the
→
insert effect ( p. 127).
3.
Press the [INPUT SOURCE] key in the control
section.
The current insert position is shown on the display.
4.
Turn the dial to select "Input 1-8".
All [ON/OFF] keys are lit in orange. In this condition, the
effect will apply to inputs 1 – 8.
HINT
The effects in the 8x COMP EQ algorithm can be switched off
ZOOM HD8/HD16