Table of Contents
Advertisement
Reference [Mixer]
3.
Use the cursor up/down keys to select the
track parameter you want to adjust.
■ Track parameter list
Parameter
Display
EQ HI GAIN
EQ HI G
(*) (S)
EQ HI
EQ HI F
FREQUENCY
(*)
EQ MID GAIN
EQ MID G
(*)
EQ MID
EQ MID F
FREQUENCY
(*)
EQ MID Q-
EQ MID Q
FACTOR (*)
EQ LOW
EQ LO G
GAIN (*) (S)
EQ LOW
EQ LO F
FREQUENCY
(*)
CHORUS/
DLY SEND
DELAY SEND
LEVEL (*) (S)
REVERB
REV SEND
SEND LEVEL
(*) (S)
SUB-OUT
SEND ON/
SUB SND
OFF (*)
SUB-OUT
SUB SEND LVL
SEND LEVEL
(*) (S)
SUB-OUT
SUB SND PAN
SEND PAN (*)
PAN
PAN (S)
Track x-y
V-TAKE
FADER
FADER
REC LVL
REC LVL
STEREO
ST LINK
LINK
INVERT
INVERT
(*): Denotes a parameter that can be switched on and off with the [ENTER] key.
(S): Denotes a parameter that can be selected with the [SELECT] key.
80
Setting range
Adjusts high-frequency boost or cut in
the range from -12 to +12 dB. This
-12 – +12dB
parameter is only shown when HI EQ
is on.
Adjusts turnover frequency for high-
500 (Hz) – 18
frequency boost/cut. This parameter is
(kHz)
only shown when HI EQ is on.
Adjusts mid-frequency boost or cut in
the range from -12 to +12 dB. This
-12 – +12dB
parameter is only shown when MID
EQ is on.
Adjusts turnover frequency for mid-
40 (Hz) – 18
frequency boost/cut. This parameter is
(kHz)
only shown when MID EQ is on.
Adjusts the Q value (bandwidth) for
0.1 – 1.0
mid-frequency EQ. This parameter is
only shown when MID EQ is on.
Adjusts low-frequency boost or cut in
the range from -12 to +12 dB. This
-12 – +12dB
parameter is only shown when LOW
EQ is on.
Adjusts turnover frequency for low-
40 (Hz) – 1.6
frequency boost/cut. This parameter is
(kHz)
only shown when LOW EQ is on.
Adjusts the chorus/delay effect send
0 – 100
level for the track/input.
Adjusts the reverb effect send level for
0 – 100
the track/input.
Selects whether the signal at the
MASTER OUT connectors (master
On/Off
track signal) is also supplied to the
STEREO SUB-OUT jack.
Adjusts the level of the signal sent from
0 – 127
the track/input to the STEREO SUB-
→
OUT jack (
Adjusts panning for the signal sent
L100 – R100
from the track/input to the STEREO
SUB-OUT jack
Adjusts the panning value of the track/
input signal. For stereo tracks, the
L100 – R100
parameter adjusts the left/right level
balance.
x=1 – 8
Selects the V-take to use for the track
→
x=1 – 16
(
p. 36). x stands for the track
y=1 – 10
number and y for the V-take number.
0 – 127
Adjusts the current volume level.
0 – 127
Adjusts the recording level.
Controls the stereo link function for
On/Off
linking two mono tracks (
Allows inverting the track/input phase.
On/Off
When set to Off, the phase is normal.
When set to On, the phase is inverted.
For a list of available parameters for tracks/inputs, see the table
below.
Mono tracks: 1 – 6 (HD8), 1 – 8 (HD16)
Stereo tracks: 7/8 (HD8), 9/10 – 15/16 (HD16)
Mono
Description
track
p. 82).
→
p. 82).
O: Valid parameter for this track/input
∆: The triangle denotes a parameter that is only
displayed when the SUB-OUT SEND LVL ON/
OFF parameter for the master track is Off.
Stereo
Master
Drum/
track
track
bass track
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
∆
∆
∆
∆
O
O
O
O
O
O
O
O
O
O
O
ZOOM HD8/HD16
Input
O
O
O
O
O
O
O
O
O
O
O
∆
∆
∆
∆
O
O
O
O
O
O
Advertisement
Table of Contents
