Sharp AR-6020V Service Manual page 55

: '19/Oct.
1
Main Sub
code code
1
<20/23 CPM>
Fusing temperature setting 4
43 04
1
<26/31 CPM>
Fusing temperature setting 2
Contents
<Fusing temperature setting 4>
When this simulation is executed, the current set values are displayed.
Switch the set value with [Concentration SW] key and press the [START] key. Then the machine writes the data into
EEPROM and is standing by the sub-code entry.
Display
lamp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
*1: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 3.) The temperature for the default, 5, becomes 5 degree C.
*2: As the setup value is increased by 1, the target temperature is increased by 5 degree C.
(See Table 3.) The temperature for the default, 3, becomes -5 degree C.
*3: Correction temperature from starting a JOB to reaching the JOB initial temperature correction no.
of sheets
*4: Correction temperature from starting a JOB to reaching the JOB latter-half temperature correction
no. of sheets
Table 3
No.
Temperature
(Degree C)
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
<Fusing temperature setting 2>
With the simulation executed, the current set values are displayed.
Switch the set value with [Concentration SW] key and press the [START] key. Then the machine writes the data into
EEPROM and is standing by the sub-code entry..
Display
lamp
1
2
3
4
5
6
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation mode is terminated.
Contents
Ready standby TH_UM set value [L environment]
Black-White plain paper TH_UM set value [L envi-
ronment]
Thin paper TH_UM set value [L environment]
Heavy paper1 TH_UM set value [L environment]
Heavy paper2 TH_UM set value [L environment]
Label paper TH_UM set value [L environment]
OHP TH_UM set value [L environment]
Envelop 1 - 9 TH_UM set value [L environment]
MM prior rotation start TH_UM set value [L environ-
ment]
MM prior rotation end TH_EX set value [L environ-
ment]
Warm-up complete time [L environment]
Alarm Stop change TH_US temperature [L environ-
ment]
Alarm Stop release TH_US temperature [L environ-
ment]
After rotating time when a job is completed [L envi-
ronment]
Preheating TH_UM set value [L environment]
TH_UM set value when Warm-Up at 120 degree C
or below [L environment]
TH_UM set value when Warm-Up at 120 degree C
or above [L environment]
Warm-Up completion time when Warm-Up at alpha
degree C or above [L environment]
TH_UM set value when Warm-Up at alpha degree
C or above [L environment]
Threshold value alpha when applying the AB to AC.
[L environment]
0 1 2 3 4
-20 -15 -10 -5 0
Contents
Black-White plain paper duplex TH_UM set value
Black-White plain paper duplex TH_US set value
Applicable paper quantity of Black-White plain paper duplex
Black-White heavy paper duplex TH_UM set value
Black-White heavy paper duplex TH_US set value
Applicable paper quantity of Black-White heavy paper duplex
AR-6020V SIMULATIONS 6-16
Details of operation
Setting Display
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
O O
5 6 7 8
5 10 15 20
Setting Display
O
O
O
O
O
O
Setup
Reference Default
range
0 - 99 A 60
0 - 99 C 55
0 - 99 D 55
0 - 99 E 55
0 - 99 F 55
0 - 99 G 55
0 - 99 H 55
0 - 99 I 55
0 - 99 J 50
0 - 99 K 56
0 - 99 L 50
0 - 99 M 50
0 - 99 N 50
0 - 99 O 50
0 - 99 S 50
0 - 99 V 55
0 - 99 Y 55
0 - 99 AB 50
0 - 99 AC 55
30 - 70 AD 50
Setup
Reference
range
70 - 220
O A
70 - 220
O B
0 - 255
O C
70 - 220
O D
0 - 200
O E
0 - 255
O F