Sharp AR-6020V Service Manual page 50

Main Sub
Contents
code code
04 Copier duplex setting
05 Count mode setting
06 Destination setting
26
07 Machine condition check (CPM)
08 Interrupt Copying setting
18 Toner save mode setting
30 CE mark conformity control ON/OFF
31 Auditor mode exclusive setup
36 Cancel of stop at maintenance life over
When this simulation is executed, the current set duplex code number is displayed. Enter the desired code number
of duplex setting and press the [START] key, and the entered code number is set.
Code number
0
1
* When this simulation is executed, the binding margin setup is automatically set to the default
(left side).
When any key input is made, it is displayed on the number of copies display. When the [START] key is pressed, the
set code data are acquired and stored to the count mode set variable and in the EEPROM, and the machine goes
into the sub code input standby mode. However, if the [START] key is pressed outside the set range, it is not
assured. At that time, when the [INTERRUPT] key is pressed, the data is not rewritten and the machine goes into
the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated without rewriting the
data.
[*1 : Total counter / Developer counter
0 (Default): *1= Double count
1: *1= Single count
2: *1= Double count
3: *1= Single count
When this simulation is executed, the current set destination code number is displayed. Enter the desired code
number of the destination and press the [START] key to set the destination.
Code number
0
1
2
3
4
5
6
If this setting is changed, SIM46-19 setting is also changed accordingly.
(The paper size is also changed: AB series is changed to A4, and Inch series to Letter.
The AUTO exposure limit setup is set to the default.
When the destination is changed (from Japan to EX Japan or from EX Japan to Japan),
the maintenance cycle is also set to the default accordingly.)
When this simulation is executed, the current setting of the machine is displayed on the number of copies display..
Code number
20
23
26
31
A copy run can be temporarily interrupted to allow another copy job to be performed.
When this simulation is executed, the current setting of the machine is displayed on the number of copies display.
Enter the desired code number of CE mark conformity and press the [START] key to set the code number.
Code number
0
1
Used to set ON/OFF of the toner save mode.
Code number
0
1
* The toner save mode of the user program is also changed accordingly.
The default value depends on the destination.
When this simulation is executed, the current set code number of CE mark conformity is displayed. Enter the
desired code number of CE mark conformity and press the [START] key to set the code number.
Code number
0
1
Used to set whether the bypass tray can be used or not when the auditor mode is set to the coin vendor mode..
Code number
0
1
2
* When this is set to "Exclusive setup ON," if the auditor is set to the coin vendor mode and the default tray is set
to the bypass tray, the default tray must be reset to the 1st tray.
Used to set stop at maintenance life over.
Code number
0
1
AR-6020V SIMULATIONS 6-11
Details of operation
Mode
Without duplex
With duplex
*2 : maintenance counter]
*2 = Double count
*2 = Double count
*2 = Single count
*2 = Single count
Destination
Japan AB series
Inch series
EX Japan AB series
EX Japan inch series (FC)
EX Japan AB series (FC) (Default)
China (EX Japan AB series + China paper support)
Taiwan (EX Japan AB series + China paper support)
Meaning (CPM information)
20CPM
23CPM
26CPM
31CPM
Meaning (CPM information)
Interrupt Copying OFF
Interrupt Copying ON
Setting
Toner save OFF
Toner save ON (Default)
Setting
CE mark conformity control OFF
CE mark conformity control ON
Setting
Exclusive setting OFF (Manual paper feed is valid)
Exclusive setting ON (Manual paper feed is invalid)
Exclusive setting OFF (Manual paper feed is valid) + A3/WLT fee
Setting
Stop at maintenance life over
Cancel of stop at maintenance life over * Default
*Default for 100V system
*Default for 200V system