Sharp AR-6020V Service Manual page 41

: '19/Oct.
1
Main Sub
code code
01 Maintenance counter display
02 Maintenance counter display
03 Jam memory display
04 Jam total counter display
05 Total counter display
06 Developing counter display
07 Mini maintenance preset display
08 RSPF counter display
09 Paper feed counter display
10 Developer counter display
14 P-ROM version display
22 15 Trouble memory display
16 Duplex print counter display
17 Copy counter display
18 Printer counter display
19 Scanner mode counter display
21 Scanner counter display
22 RSPF jam counter display
50 Developer counter display
51 Drum counter display
52 Toner counter display
53 Transfer unit counter display
54 Fusing unit counter display
01 Jam total counter clear
02 Trouble memory clear
04 RSPF counter clear
05 Duplex print counter clear
06 Paper feed counter clear
07 Drum counter clear
24 08 Copy counter clear
09 Printer counter clear
13 Scanner counter clear
14 RSPF jam total counter clear
15 Scanner mode counter clear
16 Transfer unit counter clear
17 Fusing unit counter clear
01 Main motor operation check
Auto developer adjustment (Initial setting of toner density when
25 02
replacing developer)
04 Used to display the operation data of the toner supply quantity.
02 Size setting
03 Auditor setting
04 Copier duplex setting
05 Count mode setting
06 Destination setting
07 Machine condition check (CPM)
08 Interrupt Copying setting
18 Toner save mode setting
30 CE mark conformity control ON/OFF
26
31 Auditor mode exclusive setup
36 Cancel of stop at maintenance life over
37 Cancel of stop at developer life over
38 Cancel of stop at drum life over
39 Memory capacity check
43 Side void amount setting
51 Copy temporary stop function setting
54 Life correction ON/OFF setting
69 Used to set the operating for toner end
30 01 Paper sensor status display
01 Developing counter clear
42
02 Developing counter clear (Unusable)
Contents
AR-6020V SIMULATIONS 6-2
Main Sub
code code
01 Fusing temperature setting 1
02 <20/23 CPM only> Fusing temperature setting 2
03 <20/23 CPM only> Fusing temperature setting 3
43 <20/23 CPM> Fusing temperature setting 4
04
<26/31 CPM> Fusing temperature setting 2
20 <26/31 CPM only> Fusing temperature setting 3
22 <26/31 CPM only> Fusing temperature setting 4
01 Used to set the process control operation.
Used to display the result data of the process control operation
09
1.
Used to display the result data of the process control operation
10
2.
Used to display the result data of the process control operation
44 11
3.
Used to display the result data of the process control operation
12
4.
Used to display the output level of the temperature and
14
humidity sensor.
34 Setting cleaning between jobs
02 Copy density adjustment (600dpi)
Copy exposure level adjustment, individual setting (Text)
10
600dpi
Copy exposure level adjustment, individual setting (Photo)
11
600dpi
Exposure mode setting
46
19 (Gamma table setting/AUTO exposure operation mode setting/
Photo image process setting)
20 RSPF exposure correction
29 Image contrast adjustment (600dpi)
30 AUTO exposure limit setting
31 Image sharpness adjustment
01 Main/sub scanning magnification ratio adjustment
48
RSPF mode sub scanning magnification ratio adjustment in
05
copying
01 Flash ROM program writing mode (MCU)
49
02 Flash ROM program writing mode (NNB)
01 Image lead edge adjustment
06 Copy lead edge position adjustment (RSPF)
10 Paper off-center adjustment
50
12 Document off-center adjustment
18 Memory reverse position adjustment in duplex copy
19 Rear edge void adjustment in duplex copy
01 TC ON/OFF timing adjustment
02 Resist amount adjustment
<26/31 CPM only> Used to adjust the operation timing of the
03
separate pawl.
51 <26/31 CPM only> Used to disable the operation of the
08
separate pawl.
09 Used to adjust the ON/OFF timing of the DHV voltage.
20 Polygon motor stop operation adjustment
21 1CS pick up roller adjustment.
06 Used to adjust the RSPF width detection level.
53 07 Used to set or check the RSPF width adjustment value.
08 RSPF scanning position automatic adjustment
60 01 SDRAM (image memory area) access check
01 Used to check the operation of the LSU unit.
61
03 Used to set the laser power.
63 01 Shading check
64 01 Self print
Contents
1
1