Sharp AR-6020V Service Manual page 51

Main Sub
Contents
code code
37 Cancel of stop at developer life over
38 Cancel of stop at drum life over
39 Memory capacity check
43 Side void amount setting
51 Copy temporary stop function setting
26
Life correction ON/OFF setting
54
69 Used to set the operating for toner end
When this simulation is executed, the current set code number is displayed. Enter the desired code number and
press the [START] key to set the code number. The machine goes into the sub code input state.
Code number
0
1
When this simulation is executed, the current set code number is displayed. Enter the desired code number and
press the [START] key to set the code number.
Code number
0
1
When this simulation is executed, the current memory capacity is displayed on the number of copies display.
Code number
AUTO indicator
Used to set the side void amount on the both sides.
Enter a set value with the Numeric keys and press the [START] key, and the entered value will be saved and the
machine will go into the sub code input standby mode.
The setting range is 0 - 10. When the set value is increased by 1, the void amount is increased by 0.5mm. The
default is 5 (= 2.5mm).
To select the setting mode, press the [AUTO/TEXT/PHOTO] key. The set value of the selected mode is displayed
on the copy quantity display. At that time, the set value is also saved.
LED
AUTO indicator
TEXT indicator
* When the setting value is increased by 1, time is increased by 0.5ms.
When any key is pressed, it is displayed on the display section. When the [START] key is pressed, the set code
data is acquired and stored to the setting variable of sort/group copy temporary stop function and to the EEPROM.
The machine goes into the sub code input standby mode.
Code number
0
1
When the [INTERRUPT] key is pressed at that time, the machine goes into the sub code input standby mode
without rewriting the data. When the [CA] key is pressed, the simulation mode is terminated without rewriting the
data.
* When this is set to "Stop," temporary stop is made for every 250 copies in one copy job.
Setting is made whether the image correction is made according to developer consumption degree (life progress)
or not.
When this simulation is executed, the current code number is displayed on the number of copies display.
(1=ON [Correction is performed.], 0=OFF [Correction is not performed.])
Enter the code number and press [START] key, and the setting is settled and written into the EEPROM and the
machine goes into the sub code input standby mode.
Switching can be made with [AUTO/TEXT/PHOTO] key, and the set value of the selected mode is displayed on the
number of copies display..
The setting entered at that time is written into the EEPROM.
LED
All OFF Correction in the AE1 life.
AUTO indicator Correction in the AE2 life
TEXT indicator Correction in the TEXT life
PHOTO indicator Correction in the PHOTO (Error diffusion) life
AUTO indicator & TEXT Correction in the TS AE1 life.
indicator
AUTO indicator & PHOTO Correction in the TS AE2 life.
indicator
TEXT indicator & PHOTO Correction in the TS TEXT life
indicator
AUTO & TEXT & PHOTO Correction in the PHOTO (Dither) life
indicators
This simulation used to set the operating conditions for toner end.
When this simulation is performed, the current code number is displayed.
Enter a code number and press [START] key to save the setting.
<<Operations at toner end >>
Code number
0 Operation setting 1
1 Operation setting 2
2 Operation setting 3
AR-6020V SIMULATIONS 6-12
Details of operation
Setting
Stop at developer life over
Cancel of stop at developer life over * Default
Setting
Stop at drum life over
Cancel of stop at drum life over * Default
Meaning (Memory capacity)
MCU memory amount
Side void amount (Right)
Side void amount (Left)
Setting
Not stop
Stop (Default)
Setting mode
Setting Contents
Setting mode
Default
1
1
1
1
1
1
1
1