Mitsubishi Electric 800 Series Instruction Manual page 353

(M) Monitor display and monitor output signal
Increment
Monitor item
and unit
Second PID set
0.1%
point
Second PID
0.1%
measured value
Second PID
0.1%
deviation
Second PID
0.1%
measured value 2
Second PID
manipulated 0.1%
variable
Dancer main speed
0.01 Hz
setting
Control circuit
1°C
temperature

Indication with a minus sign is not possible via RS-485 or MODBUS RTU communication.

When using the item as the main monitor data on the LCD operation panel (FR-LU08) or the parameter unit (FR-PU07), use Pr.774 to Pr.776 or
the monitor function of the FR-LU08 or the FR-PU07 for setting.

The cumulative energization time and actual operation time are accumulated from 0 to 65535 hours, then cleared, and accumulated again from
0.

The actual operation time does not increase if the cumulative running time before power OFF is less than an hour.

When using the parameter unit (FR-PU07), "kW" is displayed.

Differs according to capacities. (FR-A860-01080 or lower / FR-A860-01440 or higher)

The setting is available only for standard models.

When the output current is less than the specified current level (5% of the inverter rated current), the output current is monitored as 0 A.
Therefore, the monitored value of an output current and output power may be displayed as "0" when using a much smaller-capacity motor
compared to the inverter or in other instances that cause the output current to fall below the specified value.

Can be changed to the pulse display after the electronic gear using Pr.430 Pulse monitor selection. (Refer to
 Available when the plug-in option or control terminal option is connected.
 Input terminal monitor details ("1" denotes terminal ON, "0" denotes terminal OFF, and "―" denotes undetermined value.)
b15
― ― ―
 Output terminal monitor details ("1" denotes terminal ON, "0" denotes terminal OFF, and "―" denotes undetermined value.)
b15
― ― ―
 Option input terminal monitor 1 details (FR-A8AX input terminal status, "1" denotes terminal ON and "0" denotes terminal OFF.) ―― All are OFF
when the option is not connected.
b15
X15 X14 X13 X12
 Option input terminal monitor 2 details (FR-A8AX input terminal status. "1" denotes terminal ON, "0" denotes terminal OFF, "―" denotes
undetermined value.) ―― All are OFF when the option is not connected.
b15
― ― ―
 Option output terminal monitor details (FR-A8AY/A8AR output terminal status. "1" denotes terminal ON, "0" denotes terminal OFF, and "―" denotes
undetermined value.)―― All are OFF when the option is not connected.
b15
― ― ―
 The increment is 1 when Pr.37 = "1 to 9998" or when Pr.144 = "2 to 12, or 102 to 112". (Refer to
 The monitored values are retained even if an inverter fault occurs. Resetting will clear the retained values.
 Parameter setting is not available for setting the item as the main monitor data on the LCD operation panel (FR-LU08) or the parameter unit (FR-
PU07). Use the monitor function of the FR-LU08 or the FR-PU07 for setting.
 Negative values are not displayed on the operation panel. The values "-1 to -32767" are displayed as "65535 to 32769" on the operation panel.
 Setting of Pr.1018 Monitor with sign selection is required. Also, it will be displayed without a minus sign on the operation panel. Confirm the
rotation direction with the [FWD] or [REV] indicator.
352
PARAMETERS
Pr. setting
92 H5C
93 H5D
94 H5E
95 H5F
96 H60
97 H61
98 H62
STP
― CS RES
(STOP)
― ― ― ―
X11 X10 X9
― ― ― ―
― ― ― RA3
Negative
MODBUS
RS-485 indication
RTU
40292
40293
40294 
40295
40296 
40297
40298 
MRS JOG RH RM
― ― ABC2 ABC1
X8 X7 X6 X5
― ― ― ―
RA2 RA1 Y6 Y5
Description
(-)

Displays the set point, measured
value, and deviation under second
PID control. (Refer to
Displays PID measured value even if
PID control operating conditions are
not satisfied while the second PID
control is enabled (Pr.753 ≠ "0").
(Refer to page 497)
Displays the second PID control
manipulated amount.
(Refer to page 497)
Displays the main speed setting
under step control
Displays the temperature of the
control circuit board.
(Refer to page 390.)
Without minus sign: 0 to 100°C
With minus sign: -20 to 100°C
page 227.)
RL RT AU STR
FU OL IPF SU
X4 X3 X2 X1
― ― ―
Y4 Y3 Y2 Y1
page 345.)
page 497)
b0
STF
b0
RUN
b0
X0
b0
― DY
b0
Y0