Honeywell NOTIFIER NCA-2 Instruction Manual page 46

Operation
If a device does not exist at the selected address, an Invalid Point error message will display. Press "NEXT POINT" or "PREVIOUS
POINT" to read the next/previous programmed point of that type. If communicating with an NFS-320, NFS2-640, or NFS2-3030, the
NCA-2 will automatically proceed to the next point. In either case, an error message will indicate if there are no further devices of that type pro-
grammed.
Main menu

Read status
Display Area
Point Field
Select the device
type by scrolling
through them with
the POINT SELECT
soft key. Then,
enter the device
address in this field
to display details for
that point and press
Accept.
Main menu

Read status

Accept a point
This shows
Point Control
This shows
Point Status
Figure 4.13 Read Status Details - Smoke Detector Point Installed on an NFS-320 or NFS2-640
Figure 4.13 shows a sample status screen for a smoke detector point. Following is an explanation of the screen elements:
• Lines 1-4 can be any present event message or the System All Normal message.
• Line 5 is the screen header. It will display the current address of the point being read.
The area between the separator lines, lines 6-14, shows all information concerning the selected point, which is N003L01D051 in the
example above.
• Line 6 displays two statistics:
—Point Control:
Automatic - the point is being controlled automatically by the panel.
Manual - a status change has caused the point to go off of automatic control.
Forced - the point has been forced into another state by an outside source (such as another network node).
Disabled - the point is disabled.
—Point Status:
Active - the point is currently in an off-normal state.
Inactive - the point is currently reporting no events.
Pre-alarm - the point is in pre-alarm.
46
N O D E L A B E L F O R L O C A L N C A
P O I N T S E L E C T :
N x x x L y y D z z z
N E X T P O I N T
P R E V I O U S P O I N T
Figure 4.12 Read Status Point Select Screen
A C K N O W L E D G E D F I R E A L A R M
1
D E T E C T O R A D D R L 0 1 D 0 3 2
2
Z O N E 0 0 3
3
0 9 : 4 8 : 3 5 A T U E J A N 2 2 , 2 0 1 9
4
5
R E A D A D D R E S S : N 0 0 3 L 0 1 D 0 5 1
6
A U T O M A T I C A C T I V E
7
D E T E C T O R A D D R 1 D 0 5 1
8
Z O N E 0 3
9
Z 0 0 3 ,
1 0
1 1
V A L U E : 0 0 0 % O F A L A R M , 0 0 0 % O F P R E A L A R M
1 2
A L A R M : 8 = 2 . 1 2 % , P R E A L A R M : 8 = 1 . 3 3 %
1 3
A C T I O N / S T A T U S : N O N E / V E R Y C L E A N
1 4
P E A K : 1 4 2 % V E R I F Y C O U N T : 0 3 C O - O P : C T R
1 5
0 9 : 5 6 : 2 7 A T U E J A N 2 2 , 2 0 1 9
1 6
S Y S T E M N O R M A L
P O I N T S E L E C T
( D E T E C T O R )
Z 0 0 3 S M O K E ( P H O T O )
Z 0 0 3 S U P L ( P H O T O )
NCA-2 Manual — P/N 52482:M5 03/20/2019
The LCD Display
N o d e #
A C C E P T
B A C K
N 2 3 9 L 0 1 D 0 3 2
B A C K