Connecting A Pc For Programming; Annunciator Key Switch (Aks-1B) - Honeywell NOTIFIER NCA-2 Instruction Manual

Connecting a PC for Programming

PRN Printer Settings
Set the printer options (under the menu area) according to the settings listed in Table 3.3.
Option
L/R Adjust
Font
CPI
LPI
Skip
ESC Character
Emulate
Bidirectional Copy
I/O
Interface
Buffer
Serial
Baud
Format
Protocol *
CG-TAB
Character Set
Country
Select Zero
Auto-CR
Auto-LF
Keltron Printer VS4095/5 Settings
The printer communicates using the following protocol:
• Baud Rate
– Supervised mode: 2400
– Unsupervised mode: 300
(Supervision is a programmed setting; refer to the Panel
Programming section of the Programming Manual for
instructions.)
• Data bits: 8
• Parity: None
• Stop bits: 1
Set the printer DIP switches SP1 and SP2 according to settings in
Table 3.4.
3.15 Connecting a PC for Programming
A PC running the VeriFire
attached to J1 Network/Service Connection (NUP) or to the second Network/Service connection on an attached network communica-
tions module. Refer to the VeriFire
NOTE: Download operations that change the basic program of the control panel must be performed by responsible service personnel in
attendance at the control panel. After downloading a program, test the control panel in accordance with NFPA 72.

3.16 Annunciator Key Switch (AKS-1B)

Some jurisdictions allow one node on a network to control the network at a time; one way to meet this requirement uses AKS-1B or Con-
nector J6. For details, refer to Section 5.1 "Security Access" and your local Authority Having Jurisdiction.
The AKS-1B can provide access security for the control switches on the NCA-2. When key switch monitoring is enabled as described in
the Programming Section 5.5.7 "Supervision", the NCA-2 keypad can only be used when the AKS-1B key is inserted and unlocked.
NCA-2 Manual — P/N 52482:M5 03/20/2019
Setting for Printer Model
PRN-6 and
PRN-7
previous models
0 0
HS Draft HS Draft
10 CPI 10 CPI
6 LPI 6 LPI
0.0 0.0
ESC ESC
FX-850 LQ-2550
ON ON
Serial Serial
40K 64K
9600, 4800, 2400 9600, 4800, 2400
8 Bit, None, 1 Stop 8 Bit, None, 1 Stop
ENQ/STX ENQ/STX
Graphic Graphic
Standard Standard
E-USA ASCII E-USA ASCII
ON ON
OFF OFF
OFF OFF
Table 3.3 PRN Setup Options
®
Tools programming utility can upload and download the operating program of the control panel when
®
Tools CD for instructions.
Option PRN-6 and
previous models
Menu Lock ON
Language English
Paper
Single
Form Adjust 12/72
Trac 1
Form Adjust 12/72
Trac 2
Form Adjust 12/72
Auto Sheet Feeder
Form Adjust 12/72
Auto Tear OFF
F-Eject OFF
Form Length
Trac 1
Lines 66
Standard 10.5"
Trac 2
Lines 66
Standard 10.5"
Barcode Off
Barmode Unsecured
*Protocol: When printing in graphics mode, set I/O Serial
Protocol to "Robust XON/OFF".
Supervised Unsupervised
SP1 On Off SP1
1 X 1
2 X 2
3 X 3
4 X 4
5 X 5
6 X 6
7 X 7
8 X 8
Table 3.4 Keltron DIP Switch Settings
Installation
Setting for Printer Model
PRN-7
All
English
12/72
12/72
12/72
12/72
OFF
Top
66
11"
66
11"
Off
Unsecured
Supervised and
Unsupervised
On Off SP2 On
X 1 X
X 2 X
X 3 X
X 4 X
X 5 X
X 6 X
X 7 X
X 8 X
Off
33