Hitachi X200-002SFE/NFU Instruction Manuals page 263

B−36
The following table lists the holding registers for the "C" Group Intelligent Input Functions.
Func.
Code
C001 Terminal [1] function
C201 Terminal [1] function,
2nd motor
C002 Terminal [2] function
C202 Terminal [2] function,
2nd motor
C003 Terminal [3] function
C203 Terminal [3] function,
2nd motor
C004 Terminal [4] function
C204 Terminal [4] function,
2nd motor
C005 Terminal [5] function
C205 Terminal [5] function,
2nd motor
C011 Terminal [1] active state R/W
C012 Terminal [2] active state R/W
C013 Terminal [3] active state R/W
C014 Terminal [4] active state R/W
C015 Terminal [5] active state R/W
C021 Terminal [11] function
C026 Alarm relay terminal
function
C028 [AM] signal selection
C031 Terminal [11] active
state
C036 Alarm relay active state
C038 Output mode of low load
detection signal
C039 Low load detection level
C041 Overload level setting
C241 Overload level setting,
2nd motor
C042 Frequency arrival
setting for acceleration
C043 Frequency arrival
setting for deceleration
More user manuals on
Name R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W Two available functions:
R/W Select logic conversion:
R/W Select logic conversion:
R/W Three option codes:
R/W Set the level of low load detection,
R/W
R/W
R/W Sets the frequency arrival setting
R/W Sets the frequency arrival setting
ManualsBase.com
List of Holding Registers
Description
See "Input Terminal Configuration"
on page 3-49
Select logic conversion, two option
codes:
00...normally open [NO]
01...normally closed [NC]
See "Output Terminal
Configuration" on page 3-54
00...motor speed
01...motor current
00...normally open [NO]
01...normally closed [NC]
00...normally open [NO]
01...normally closed [NC]
00...Disabled
01...During acceleration,
deceleration and constant speed
02...During constant speed only
range is 0.0 to 2.0*rated current
Sets the overload signal level
between 0% and 200% (from 0 to two
time the rated current of the
inverter)
threshold for the output frequency
during acceleration,
range is 0.0 to 400.0 Hz
threshold for the output frequency
during deceleration,
range is 0.0 to 400.0 Hz
Network Data
Reg. Range Res.
1103h 0, 1, 2, 3, −
4, 5, 6, 7,
1532h
8, 9, 11,
12, 13,
1104h
15, 16,
1533h
18, 19,
20, 21,
1105h
22, 23,
1534h
24, 27,
28, 29,
1106h 31, 50,
51, 52,
1535h
53, 64,
255
1107h
1536h
110Bh 0, 1 −
110Ch 0, 1 −
110Dh 0, 1 −
110Eh 0, 1 −
110Fh 0, 1 −
1114h 0, 1, 2, 3, −
4, 5, 6, 7,
1119h −
8, 9, 10,
43
111Bh 0, 1 −
111Dh 0, 1 −
1122h 0, 1 −
1178h 0, 1, 2 −
1179h 0 to 0.01%
20000
1124h 0 to 0.01%
20000
153Ah
1126h 0 to 4000 0.1 Hz
*1
1128h 0 to 4000 0.1 Hz