Subaru 1600 Service Manual page 610

Movement of glass
A. Frontward/rearward shift
C. Frontward/rearward inclination
B. Uppermost position
D. Inward/outward shift of glass
bottom at uppermost position
E. Inward/outward shift of glass top
at uppermost position
NOTE:
When frontward/rearward shift adjust-
ment of door glass is necessary, refer
to door glass adjustment for Hardtop,
because adjusting measure for Hardtop
is different from that for 4-Door
Sedan and Station Wagon.
A Adjustment of contact pressure
1) Close the door glass all the way,
and temporarily adjust the gaps to
the dimensions shown in the follow-
ing figure by moving side window
glass upward/downward and front-
ward/rearward.
(Shift door glass frontward or rear-
ward by adjusting rear sash of door as
reqired. Refer t" the door section.)
~
LJ
6±2 (0.24±0.OS)
.....
Door glass
Unit:
mm
(in)
A24-449
Fig. 14-30 Dimensions of gaps
2) Fix the stopper A.
Flange nut
tightening
torque
7 -9
N·m
(0.7 - 0.9 kg-m,
5.1 - 6.5 ft-lb)
BODY
Adjusting measure
Moving positions of guide plate by
loosening three nuts of upper and
lower adjuster
Moving positions of stopper A and B
Screw or unscrew two bolts of upper
adjuster
Screw or unscrew one bolt of lower
adjuster
3) Open door glass all the way.
4) Position the glass at the window
shoulder as shown in the following
figure by revolving two bolts of upper
adjuster with screwdriver.
Out
In
Approx. 17.S (0.701)
(Parallel)
=
~ ~
c>
C:I>
-----c:::o...cs
~
Approx.17.S (0.701)
(Parallel)
Unit:
mm
(in)
A24-450
Fig. 14-31 Adjusting contact pressure
at window shoulder
Then make sure that the gap between
glass and weatherstrip retainer at rear
pillar corresponds to the dimension
shown in the follOWing figure. Adjust
the gap by upper adjust bolt, if
necessary.
~ 3:~~
. (0.12 - 0.20 in)
9 - - - - -
Approx. 5 em (2.0 in)
A24-451
Fig. 14-32 Adjusting contact pressure
at rear pillar
14-15
Adjustable length of adjuster
5 mm (0.20 in) forward &
5 mm (0.20 in) rearward
5 mm (0.20 in) upward &
5 mm (0.20 in) downward
3.5 mm (0.138 in) inward &
3.5 mm (0.138 in) outward
8 mm (0.31 in) inward &
8 mm (0.31 in) outward
5) Adjust the gap between glass and
weatherstrip retainer at the top of the
glass to the dimension shown in the
following figure by revolving the bolt
of lower adjuster.
Fig. 14-33
A24-452
B Adjustment of gap
1)
Loosen two nuts of upper adjuster
and one nut oflower adjuster.
2) Applying a little upward force
to the glass by the regulator handle,
adjust the position and inclination of
the glass so that the gap between the
rear edge of glass and weatherstrip re-
tainer corresponds the dimension
shown in the following figure, and
then fix three nuts and stopper
B.
Tightening torque
Flange nuts
18 - 23 N·m
(1.8 - 2.3 kg-m,
of adjuster
13 - 17 ft-Ib)
Hex. bolt
5 -7 N·m
fixing
(0.5 - 0;7 kg-m,
stopper B
3.6 - 5.1 ft-Ib)