JRC JMA-5912-6 Instruction Manual page 459

7 PLOT Menu 3 WPT/Route Settig
4 WPT/Route Operation
5 Clear Memory
6 Plot Setting
7 NMEA Waypoint Display
9 Next
Press RADAR MENU again
1 File Manager → Section 3.11.1
2 RADAR Menu － 1 Process Setting
3 TXRX Setting
－ 1 Waypoint Alarm
2 Route Alarm
（Route Type：Plotter）
3 Set Route Sequence
4 Select Route
5 Waypoint Entry
6 Waypoint Input
7 Save Temporary Route
8 Cross Track Limit Line
9 Next
↓
1 Select WPT Mark Size
2 Waypoint Vector
3 Status of Origin/DEST
4 WPT Number Display
5 RTE Number Display
－ 1 Route Sequence
2 Waypoint Switch Mode
3 Waypoint Skip
4 Waypoint Back Skip
5 Set/Cancel Waypoint
1 Clear Mark/Line Data
－
2 Clear WPT/Route Data
－ 1 Scale/Course Up Setup
2 Current Position Display
3 Cursor Vector DISP
4 Cursor HL Length
5 Scalebar Display
6 AUTO Backup
→ Section 3.7.1
－ 1 Video Latitude
2 Video Noise Rejection
3 AUTO Dynamic Range
4 Process Switch
5 2nd Process Mode
6 Process Switch Range
7 Fast Target Detection
8 User Function Setting
9 SART
－ 1 PRF Fine Tuning
2 Stagger Trigger
4 PRF
5 Ice Class Standby Mode
→ Section 3.6.2
－ 1 Scale
2 Preset Scale
3 Course Up Data
－
→ Section 3.8.1
→ Section 3.8.1
→ Section 3.8.1
→ Section 3.8.1
→ Section 3.8.1
→ Section 3.8.1
→ Section 3.8.1
－ 1 Function1 Setting －
2 Function2 Setting → Section 3.9.3
3 Function3 Setting → Section 3.9.3
4 Function4 Setting → Section 3.9.3
→ Section 6.5
→ Section 3.8.3
→ Section 3.8.3
→ Section 3.8.3
→ Section 3.8.3
1 Tolerance
2 Averaging
3 Round Speed
1 Mode → Section 3.9.3
2 IR → Section 3.9.3
3 Process → Section 3.9.3
4 Target Enhance → Section 3.9.3
5 AUTO Sea/Rain → Section 3.9.3
6 Save Present State → Section 3.9.3
9 Next
↓
1 Pulse Length 0.75nm → Section 3.9.3
2 Pulse Length 1.5nm → Section 3.9.3
3 Pulse Length 3/4nm → Section 3.9.3
4 Pulse Length 6/8nm → Section 3.9.3
5 Pulse Length 12nm → Section 3.9.3
6 Pulse Length 16nm → Section 3.9.3
9 Next
↓
1 Video Latitude → Section 3.9.3
2 Video Noise Rejection → Section 3.9.3
3 AUTO Dynamic Range → Section 3.9.3
4 Process Switch → Section 3.9.3
5 2nd Process Mode → Section 3.9.3
6 Process Switch Range → Section 3.9.3
7 Fast Target Detection → Section 3.9.3
9 Next
↓
1 Trails Interval → Section 3.9.3
2 Trails Mode → Section 3.9.3
3 Trails Reference Level → Section 3.9.3
4 Trails Reduction → Section 3.9.3
5 Time/All Combine → Section 3.9.3
6 Trails Process → Section 3.9.3
7 Max Interval → Section 3.9.3
9 Next → Section 3.9.3
↓
1 Gain Offset → Section 3.9.3
2 PRF → Section 3.9.3
3 Small Buoy Detection → Section 3.9.3
4 Fishnet Detection → Section 3.9.3
5 Antenna Height → Section 3.9.3
8 Set Mode Default → Section 3.9.3
9 Initialize → Section 3.9.3