User Responsibilities; Safety Warnings; Warning, Error And Alarm Messages - Pentair raychem ngc-30/uit2 Programming Manual

1.4 user resPonsiBiLities

1.5 saFety WarninGs

1.6 WarninG, error and aLarm messaGes

industrial heat tracing solutions
Restricted Rights clause at 48 C.F.R. 52.227-19, as applicable. This provision applies to the
Raychem NGC-30 Software acquired directly or indirectly by or on behalf of any government.
The Raychem NGC-30 Software is a commercial product, licensed on the open market at
market prices, and was developed entirely at private expense and without the use of any
government funds. Any use, modification, reproduction, release, performance, display, or
disclosure of the Raychem NGC-30 Software by any government shall be governed solely by
the terms of this Agreement and shall be prohibited except to the extent expressly permitted by
the terms of this Agreement, and no license to the Raychem NGC-30 Software is granted to any
government requiring different terms.
13. assiGnment. You may neither assign any right nor delegate any obligation under this
Agreement and attempted assignment or delegation shall be void. Pentair Industrial Heat
Tracing Solutions may freely assign this agreement and its rights and obligations there under
to any third party.
14. inVaLid ProVisions. If any of the provisions of this provisions Agreement are invalid under
any applicable statute or rule of law, they are to that extent deemed omitted.
15. WaiVer. No failure or delay of Pentair Industrial Heat Tracing Solutions in exercising or
enforcing any right or provision of this Agreement shall constitute a waiver of such right
or provision, or any other right or provision hereunder. Furthermore, any waiver by Pentair
Industrial Heat Tracing Solutions of any right or provision of this Agreement shall not be
construed as, or constitute, a continuing waiver of such right or provision, or waiver of any
other right or provision of this Agreement.
16. headinGs. The section titles in this Agreement are for convenience only.
17. surViVaBiLity. You agree that the terms and conditions of this Agreement shall survive any
termination of this Agreement and your rights to use the Software.
Should you have any questions concerning this Agreement, or if you desire to contact Pentair
Industrial Heat Tracing Solutions for any reason, please write to:
Pentair Industrial Heat Tracing Solutions
307 Constitution Drive
Menlo Park, CA 94025-1164
U.S.A.
The performance, reliability and safety of your heat-tracing system depend on proper design,
selection, and installation. The Raychem NGC-UIT2-EX Software will help you configure and
monitor a system that meets your requirements, but it is only a tool. It assumes that your input
is accurate, that you are familiar with heat-tracing system design and configuration, and that you
will ensure that all components of the heat-tracing system are installed, maintained and used
as intended. The configuration of the Raychem NGC-UIT2-EX Software should be reviewed by a
knowledgeable engineer to ensure it is appropriate for your application. Additional information
relating to safety, design, and installation is contained in Design Guides, Installation Manuals,
Data Sheets, and other literature available from Pentair Industrial Heat Tracing Solutions. Be sure to
consult these documents as needed.
There are important safety warnings which are shipped with Pentair Industrial Heat Tracing
Solutions products and that are also printed in the Raychem NGC-20 Installation Manual
(ML-RaychemNGC20CLE-IM-INSTALL130) and Raychem NGC-30 Installation Manual (H57878). Be
sure to read and follow these safety warnings to reduce the risk of fire, shock, or personal injury.
If you have any questions, contact your local representative or contact Pentair Industrial Heat
Tracing Solutions directly.
Under certain conditions, the Raychem NGC-30 program will alert the user with a warning or an
error message. These are typically either because the program cannot find an acceptable answer
based on user input, or because the user may need to take some additional action to ensure the
design requirements are completely met. These warnings and error messages are detailed on
page 52.
EN-RaychemNGC30UIT2Programming-AR-H58186 02/16 9 / 84