Mitsubishi FX3G Series Programming Manual page 9
Programmable controllers
Hide thumbs
Also See for FX3G Series:
- User manual (382 pages) ,
- Installation manual (3 pages) ,
- User manual (240 pages)
Table of Contents
Advertisement
FX
/FX
/FX
/FX
3G
3U
3GC
3UC
Programming Manual - Basic & Applied Instruction Edition
12.1 FNC 40 - ZRST / Zone Reset............................................................................................................ 310
12.2 FNC 41 - DECO / Decode ................................................................................................................. 313
12.3 FNC 42 - ENCO / Encode ................................................................................................................. 316
12.4 FNC 43 - SUM / Sum of Active Bits................................................................................................... 318
12.5 FNC 44 - BON / Check Specified Bit Status...................................................................................... 321
12.6 FNC 45 - MEAN / Mean .................................................................................................................... 323
12.7 FNC 46 - ANS / Timed Annunciator Set............................................................................................ 325
12.8 FNC 47 - ANR / Annunciator Reset................................................................................................... 327
12.9 FNC 48 - SQR / Square Root............................................................................................................ 328
12.10 FNC 49 - FLT / Conversion to Floating Point .................................................................................. 329
13.1 FNC 50 - REF / Refresh .................................................................................................................... 332
13.1.1 What should be understood before using the REF instruction............................................................ 335
13.2 FNC 51 - REFF / Refresh and Filter Adjust....................................................................................... 336
13.2.1 What should be understood before using REFF instruction................................................................ 338
13.3 FNC 52 - MTR / Input Matrix ............................................................................................................. 339
13.3.1 Operation and cautions for the MTR instruction.................................................................................. 342
13.4 FNC 53 - HSCS / High-Speed Counter Set....................................................................................... 343
13.4.1 Common cautions on using instructions for high-speed counter ........................................................ 346
13.5 FNC 54 - HSCR / High-Speed Counter Reset .................................................................................. 349
13.6 FNC 55 - HSZ / High-Speed Counter Zone Compare....................................................................... 352
[ZCP (FNC 11) instruction].................................................................................................................. 356
13.6.2 Table high-speed comparison mode (M8130) .................................................................................... 358
13.6.3 Frequency control mode (HSZ and PLSY instructions) (M8132) ........................................................ 361
13.7 FNC 56 - SPD / Speed Detection...................................................................................................... 364
13.8 FNC 57 - PLSY / Pulse Y Output ...................................................................................................... 368
13.9 FNC 58 - PWM / Pulse Width Modulation ......................................................................................... 373
13.10 FNC 59 - PLSR / Acceleration/Deceleration Setup ......................................................................... 376
14.1 FNC 60 - IST / Initial State ................................................................................................................ 382
14.1.1 IST instruction equivalent circuit ......................................................................................................... 384
14.1.2 Example of IST instruction introduction (example of workpiece transfer mechanism)........................ 385
14.2 FNC 61 - SER / Search a Data Stack ............................................................................................... 392
14.3 FNC 62 - ABSD / Absolute Drum Sequencer.................................................................................... 395
14.4 FNC 63 - INCD / Incremental Drum Sequencer ................................................................................ 398
14.5 FNC 64 - TTMR / Teaching Timer..................................................................................................... 400
14.6 FNC 65 - STMR / Special Timer........................................................................................................ 402
14.7 FNC 66 - ALT / Alternate State ......................................................................................................... 404
14.8 FNC 67 - RAMP / Ramp Variable Value ........................................................................................... 406
14.9 FNC 68 - ROTC / Rotary Table Control ............................................................................................ 408
14.10 FNC 69 - SORT / SORT Tabulated Data ........................................................................................ 411
15.1 FNC 70 - TKY / Ten Key Input .......................................................................................................... 415
15.2 FNC 71 - HKY / Hexadecimal Input................................................................................................... 418
15.3 FNC 72 - DSW / Digital Switch (Thumbwheel Input)......................................................................... 422
15.4 FNC 73 - SEGD / Seven Segment Decoder ..................................................................................... 425
15.5 FNC 74 - SEGL / Seven Segment With Latch................................................................................... 427
15.5.1 How to select a seven-segment display unit ....................................................................................... 430
15.5.2 How to select parameter "n" based on seven-segment display specifications ................................... 430
15.6 FNC 75 - ARWS / Arrow Switch ........................................................................................................ 432
15.7 FNC 76 - ASC / ASCII Code Data Input............................................................................................ 436
15.8 FNC 77 - PR / Print (ASCII Code) ..................................................................................................... 438
Series
Table of Contents
309
331
381
414
7
Advertisement
Table of Contents
