System Configurations - Xerox Phaser 8560MFP Service Documentation

System Configurations

Standard Features
The Phaser 8510/8560MFP offers these standard features:
• Maximum print speed (pages per minute) based on letter-size plain paper:
NOTE: Print speeds for media fed from Tray 1 may be up to 50% slower.
Table 1 Phaser 8510/8560MFP Print Speeds
Phaser 8510MFP Multifunction Product
PostScript Print Quality Modes:
– Fast Color: 24 ppm
– Enhanced: 12 ppm
PCL Print Quality Modes:
– 300 x 600 dpi: 13 ppm
– 600 x 600 dpi: 6 ppm
• First-page-out: 8 seconds for color prints, 15 seconds for color copies
• Copy, Print, Scan, Fax capabilities (options vary according to configuration and memory)
• Connections: USB, Ethernet 10/100/1000 Base-Tx, RJ-11 Fax Modem, Foreign Device
Interface
Available Configurations
Table 2 lists the standard configurations.
Table 2 Phaser 8510/8560MFP Standard Configurations
Features 8510MFP/N 8510MFP/D
Memory 512 MB 512 MB
(2x256)
Hard Drive No
Flash Disk Yes
Automatic 2-sided No
Printing (DADF)
525-Sheet Feeder No*
System Cart No*
Copy Yes
Scan to PC Yes
Scan to E-mail Yes
Scan to Hard Drive No
Fax Yes
* This option can be purchased separately for this configuration.
** Hard Drive enables advanced features on this configuration.
Initial Issue
Phaser 8510/8560MFP Multifunction Product
Phaser 8560MFP Multifunction Product
PostScript Print Quality Modes:
– Fast Color: 30 ppm
– Standard: 24 ppm
– Enhanced: 16 ppm
– High Resolution/Photo: 10 ppm
PCL Print Quality Modes:
– 300 x 600 dpi: 16 ppm
– 600 x 600 dpi: 8 ppm
8560MFP/D 8560MFP/T 8560MFP/X
512 MB 512 MB
No Yes Yes
Yes No No
Yes Yes Yes
No* No* Yes
No* Yes Yes
Yes Yes** Yes**
Yes Yes Yes
Yes Yes Yes
No Yes Yes
Yes Yes** Yes**
Product Options
Phaser Multifunction Product options include:
• Additional Trays
• Memory
• System Cart
Additional Trays
Trays 1 and 2 are standard on all configurations. The following additional tray combinations are
supported:
• One 525-Sheet Feeder (Tray 3)
• Two 525-Sheet Feeders (Trays 3 and 4)
Memory
All configurations have two memory slots supporting 512 MB, and 1 GB SODIMM modules (up
to maximum of 1 GB DDR2).
System Cart
The System Cart supports a fully-optioned system and provides space for media storage.
Metered Printing
Metered printing (PagePack), involves the combination of control software and specialized Ink
Sticks to meter system activity for billing purposes. The Configuration page lists Metered Ink as
Enabled when metering is enabled.
Metered Operation
When a metered printer is initialized at first power-up, the customer sets the printer to Metered
operation using a unique, factory-supplied, 4-digit PIN. Once set to Metered operation, the con-
trol software performs the following:
1. The Mode and PIN-entered values in Engine Control Board NVRAM are set.
512 MB
2. The Control Panel momentarily displays "Metered Ink is now enabled", then returns to
"Ready" (if no other errors).
Yes
3. The First Time Tips pages and the Configuration page are printed.
No
If an incorrect PIN is entered, "Incorrect numeric password" displays with a prompt "Retry" or
Yes "Do not retry." Retry returns to the enter prompt, "Do not retry" returns to the Replace Ink Stick
error message. The error persists until the correct PIN is entered.
Yes
NOTE: The Hidden Service menu provides an Enable Metered Ink option to restore the
Yes
Metered mode parameters to NVRAM should they become lost or corrupt.
Yes**
Metered Ink
Yes
To support metered printing, metered Ink Sticks are available in all four colors. The shape of
Yes
the metered Ink Stick differs from the non-metered versions.
Yes
Yes**
10/2006
xiii
Introduction
System Configurations