Regency HZ33CE-NG Owners & Installation Manual

Hide thumbs Also See for HZ33CE-NG:
Table of Contents

Advertisement

Quick Links

Regency HZ33CE
WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.
Tested by:
919-120a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
Gas Fireplace
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Owners &
Installation Manual
MODEL: H
H
www.regency-fi re.com
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fi re department.
Z3
3CE-NG Natural Gas
Z3
3CE-LP Propane
HZ33CE Video
11/13/13

Advertisement

Table of Contents
loading

Summary of Contents for Regency HZ33CE-NG

  • Page 1 Owners & Regency HZ33CE Installation Manual Gas Fireplace MODEL: H 3CE-NG Natural Gas 3CE-LP Propane HZ33CE Video www.regency-fi re.com WARNING: FOR YOUR SAFETY If the information in these instructions are not followed exactly, What to do if you smell gas: a fi...
  • Page 2 Congratulations! ® You are the owner of a state-of-the-art Gas Fireplace by REGENCY . The HZ33CE has been designed to provide you with all the warmth and charm of a fi re at the fl ick of a switch. The model HZ33CE has been approved by Warnock Hersey for both safety and effi...
  • Page 3: Manufactured Mobile Home Requirements

    This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certifi ed kit is used. (Kit # 434-972). Ensure that structural members are not cut or weakened during installation. Regency HZ33CE Gas Fireplace...
  • Page 4: Table Of Contents

    High Elevation .............30 The Warranty: Limited Lifetime ........59 886 S.I.T. Valve Description .........30 Gas Pipe Pressure Testing ..........30 Conversion from NG to LP ..........31 Wiring Diagrams ............35 Profl ame system GT ...........35 Profl ame system GTM ..........36 Regency HZ33CE Gas Fireplace...
  • Page 5: Safety Label

    The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed. Regency HZ33CE Gas Fireplace...
  • Page 6: Requirements

    (e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. Regency HZ33CE Gas Fireplace...
  • Page 7: Dimensions

    584mm 2-1/2" 34-9/16" [64mm] [878mm] NAILING STRIP 3" (76mm) 26" 660mm 29-7/16" 747mm 4 SIDED FACEPLATE DIMENSIONS MANTEL DIMENSIONS 42-5/16" (1074mm) 47-9/16" 5-1/8" (1207mm) 9" (76m (130mm) (229mm) 29-9/16" 8-1/8" (750mm) (206mm) 2" (51mm) 52-1/8" (1324mm) Regency HZ33CE Gas Fireplace...
  • Page 8: Installation

    4. This appliance must be connected to the speci- fi ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is fi tted as per Venting instructions. Regency HZ33CE Gas Fireplace...
  • Page 9: Installation Checklist

    fi replaces. 11. Final check. Flat on Wall Corner Before leaving this unit with the customer, the Recessed into Wall/Alcove installer must ensure that the appliance is fi ring Corner correctly and operation fully explained to customer. Regency HZ33CE Gas Fireplace...
  • Page 10: Clearances

    Vertical (Rigid) 1-1/4" D: Alcove Width 84" (1219mm) Sidewall to Sidewall (Minimum) E: Alcove Depth 36" (914mm) Front to Back Wall (Maximum) F: Mantel 12" (305mm) G: Mantel Clearances From Top Opening of Unit 15-3/4" (400mm) Regency HZ33CE Gas Fireplace...
  • Page 11: Mantel Clearances

    Standoff 24-1/4"(616mm) Top opening to floor of Unit Side View MANTEL LEG CLEARANCES Combustible mantel leg clearances from side of unit as per diagram: Top View Side opening of Unit 6-3/4" Allowable mantel leg projection 9" Regency HZ33CE Gas Fireplace...
  • Page 12: Framing & Finishing

    Non-combustible Material (3-1/2" x 34-9/16") Supplied with Unit Non-combustible Nailing Strip -1/2" back from unit face Finishing Material (ie. tile) Ensure finished material is brought to lip Non-combustible Finishing Material (ie. tile) Combustible Material 29-7/16" 747mm Regency HZ33CE Gas Fireplace...
  • Page 13: Clean Finish

    To maintain a clean fi nished edge - facing material edges may be fi nished with a J-style trim or metal cornerbead (both materials available at your local building or hardware store). IMPORTANT: Materials used must be NON-COMBUSTIBLE. Regency HZ33CE Gas Fireplace...
  • Page 14: Framing Dimensions

    36" (914mm) Rigid 32" (812mm) Flex Vent Centerline Height* 30" (762mm) Rigid 26" (660mm) Flex Gas Connection Height* 1 1/2" (38mm) Gas Connection Inset* 7-3/16" (183mm) Gas Connection Width* 3" (76mm) * Measured from base of unit. Regency HZ33CE Gas Fireplace...
  • Page 15: Venting Introduction

    ® There are 5 vent systems approved for use with the HZ33CE: the Regency Direct Vent Flex System for Horizontal Terminations only and the Simpson Dura-Vent, Selkirk Direct-Temp, Amerivent Direct Vent and Security Secure Vent Systems for Horizontal and Vertical Terminations (see following "Venting"...
  • Page 16: Exterior Vent Termination Requirements

    * Clearance in accordance with local installation codes and the requirements of the gas supplier 3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly 3 feet (91cm) above - if within 10 feet (3m) horizontally Regency HZ33CE Gas Fireplace...
  • Page 17: Regency ® Direct Vent Fl Ex System

    (8. screws #8 x 1-1/2" drill point, stainless steel (4. Notes: 1. Liner sections should be continuous without any joints or seams. 2. Only Flex pipe purchased from Regency ® may be used for Flex installations. Alternate Horizontal Termination...
  • Page 18: Rigid Pipe Venting Systems

    American Metal Products Ameri Vent Direct Vent, Security Secure Vent , Selkirk Direct-Temp. AstroCap is a proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. Regency HZ33CE Gas Fireplace...
  • Page 19: 4" X 6-5/8" Rigid Pipe Cross Reference Chart

    Offset Support 46DVA-ES (N/A - FPI) 4DT-OS SV4SU Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM TE-4DE90 Wall Thimble Support/Ceiling Support 46DVA-DC SV4PF TE-4DE90B Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF Trim Plate-Black 4DT-TP 4DFPB 4DCP SV4LA Regency HZ33CE Gas Fireplace...
  • Page 20 Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination. Never allow the vent to run downward - this could cause high temperatures and may present a possible fi re hazard. Regency HZ33CE Gas Fireplace...
  • Page 21: Rigid Pipe Venting Arrangements

    Firestops are required at each fl oor level and whenever passing through a wall. • Maintain clearances to combustibles. • Vent must be supported at offsets. Note: Must use optional rigid pipe adapter when using rigid vent systems (Part # 510-994.. Regency HZ33CE Gas Fireplace...
  • Page 22: Vertical Termination With Co-Linear Flex System

    46DVA-VCH High Wind Cap 46DVAGK 3" Co-linear Adapter with fl ashing Outer Pipe with Kit# 946-563 Air Intake Pipe Length Co-Linear Flex Rigid Pipe Adaptor Adapter # 510-994 with Kit# 946-563 45 Elbow Inner Pipe Adapter with Kit# 946-563 Regency HZ33CE Gas Fireplace...
  • Page 23: Venting Arrangements - Vertical Terminations

    VENTING ARRANGEMENTS - VERTICAL TERMINATIONS with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces Horizontal Distance (Feet) Horizontal Distance (Feet) Horizontal Distance (Feet) The shaded area in the diagrams show the allowable vertical terminations. Regency HZ33CE Gas Fireplace...
  • Page 24 Maintain clearances to combustibles. 8"(0.2m) • Horizontal vent must be supported every 3 feet. • Firestops are required at each fl oor level and whenever passing through a wall. 2’ (0.6m) Minimum Minimum Simpson Dura-Vent Center-Line Flex Kit Center-Line Regency HZ33CE Gas Fireplace...
  • Page 25 5' Max. vertical and maximum 8 feet total horizontal. 3' Max. 4' Min. 6' Max. Please note minimum 4' Max. 6' Min. 7' Max. 1 foot between 90 elbows is required. 5' Max. 8' Min. 8' Max. Regency HZ33CE Gas Fireplace...
  • Page 26 5' Min. 1 foot between 90 required. elbows is required. 5' Min. 8' Max. 6' Min. 6' Max. 6' Min. For additional vertical venting with 2 x 90 elbows, refer to "Rigid Pipe Venting Arrangements" Section. Regency HZ33CE Gas Fireplace...
  • Page 27 8 feet total horizontal. 4' Min. 5' Max. 7' Min. Please note min. 1 foot 5' Min. 6' Max. 8' Min. between 90 elbows is 6' Min. 7' Max. 9' Min. required. 7' Min. 8' Max. 10' Min. Regency HZ33CE Gas Fireplace...
  • Page 28: Unit Installation With Horizontal Termination

    “Mill-Pac” sealant (supplied) to every in- pipe. ner pipe connection. Failure to do so may result in drafting or performance issues not covered under warranty. Silicone (red RTV) is optional. b) Horizontal runs of vent must be Regency HZ33CE Gas Fireplace...
  • Page 29: Unit Installation With Vertical Termination

    7. Ensure vent is vertical and secure the base of the fl ashing to the roof with roofi ng rails, slide storm collar over the pipe section and seal with a mastic. Diagram 2 8. Install the vertical termination cap by twist- Regency HZ33CE Gas Fireplace...
  • Page 30: Pilot Adjustment

    INSTALLATION GAS PIPE PRESSURE PILOT ADJUSTMENT HZ33CE-NG System Data TESTING Periodically check the pilot fl ames. Correct fl ame pattern has two strong blue fl ames: Conversion Kit# 434-972 (NG to LP) The appliance must be isolated from the gas 1 fl...
  • Page 31: Conversion From Ng To Lp

    11. Reverse steps 2 - 1. Diagram 1 12. Check for gas leaks. 13. Check inlet and outlet pressures. 14. Check operation of fl ame control. Diagram 4 Installer Notice: These instructions must be left with the appliance Regency HZ33CE Gas Fireplace...
  • Page 32: Gt Remote Installation

    (white) 12) Reverse steps 5 and 4. (green) 13) Match the remote control to the receiver - see remote control instructions. 14) Reverse steps 2 and 1. 15) Check to ensure there are no gas leaks. Regency HZ33CE Gas Fireplace...
  • Page 33: Gtm Remote Installation

    4) Remove DFC (digital fi rebox control box) from the fl oor of the unit. 9) Remove the hi/lo knob if installed by removing 2 screws as shown below. 5) Disconnect wire harness, ground wire and spark wire from DFC. Regency HZ33CE Gas Fireplace...
  • Page 34 19) Reverse steps 2 and 1. 20) Check to ensure there are no gas leaks. 14) To unattach these wires - un-clip from the wires on the stepper motor side as shown below. Press down this tab Regency HZ33CE Gas Fireplace...
  • Page 35: Wiring Diagrams

    If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve. PROFLAME SYSTEM GT Proflame System Configuration 886 GTMF Wire Diagram SureFire™ Switch Optional AC Adaptor Regency HZ33CE Gas Fireplace...
  • Page 36: Profl Ame System Gtm

    If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve. Proflame System Configuration 886 GTMF Wire Diagram SureFire™ Switch Optional AC Adaptor Regency HZ33CE Gas Fireplace...
  • Page 37 4) Plug AC adaptor into 120V wall outlet (or into 120V receptacle if see manual for location in unit. 5) Neatly tuck any loose AC Power Adaptor wires neatly underneath / inside the appliance. Note: (keep wires away from the heat as much as possible). FCM - COM Regency HZ33CE Gas Fireplace...
  • Page 38: Installing The Optional Fan (Prior To Unit Installation)

    These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan blades and housing using a soft brush nozzle. Diagram 4 Regency HZ33CE Gas Fireplace...
  • Page 39: Optional Fan Wiring Diagram

    4. Remove glass crystals or ceramic stones. 5. Remove the base tray by removing 6 screws in the locations shown below. Diagram 2 Diagram 1: Remove the 6 screws and then lift out the base tray Regency HZ33CE Gas Fireplace...
  • Page 40 These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan blades and housing using a soft brush nozzle. Diagram 6 Regency HZ33CE Gas Fireplace...
  • Page 41: Optional Wall Thermostat

    1. 4 AA batteries must be installed in the battery pack to operate the burner switch. 2. Install 2 AA batteries per side and connect as shown below - the battery pack is located on the lower left side of the unit. Regency HZ33CE Gas Fireplace...
  • Page 42: Optional Refl Ective Panel Installation

    4. With the top panel in place - install back panel. The back panel fi ts under the top panel, push the top panel up to fi t back panel into position. (Diagram 3) Completed Panel Installation Note: Diagram is shown without a burner. Diagram 3 Back Panel Regency HZ33CE Gas Fireplace...
  • Page 43: Glass Crystals And Optional Stones

    The Burner and Firebox Floor should not be visible when the fl ame is out. OPTIONAL SPA STONES INSTALLATION (AROUND BURNER NOTE: Spa stones are NOT to be placed anywhere on the burner tube or Pilot assembly area. Regency HZ33CE Gas Fireplace...
  • Page 44: Optional Log Set Installation

    HZ33CE shown - Logs 1 and 5 in position. 9. Place Log 4 on the glass on the right side in location shown below. HZ33CE - install bracket, left side HZ33CE shown - Logs 1,4 and 5 in position. Regency HZ33CE Gas Fireplace...
  • Page 45 3. Position Log 2, line up pin landing on Log 2 with pin on Log 1, remainder of Log 2 rests on the burner tray as shown below. 13. Adjust aeration, see unit manual for setting. HZ30E use top pin landing HZ33CE shown - Final Install HZ30E shown - installing Log 2 Regency HZ33CE Gas Fireplace...
  • Page 46 6. Place lava embers/rocks on glass - ensure rocks do not block pilot. Do not place lava rocks/embers too close to logs as this may cause carboning. 7. Adjust aeration, see unit manual for setting. HZ30E shown - Final Install Regency HZ33CE Gas Fireplace...
  • Page 47: Glass Screen Guard And Glass Door Installation

    Use the hook to pull the spring out until you can put the hook into the slot on the bottom door bracket. Repeat for 2nd spring. See Diagram 4. Diagram 4 To remove the fl ush door and screen, reverse the above steps. Regency HZ33CE Gas Fireplace...
  • Page 48: Optional 4-Sided Faceplate Installation

    Diagram 2 -Bracket screw locations on unit. 2. Install four (4) wood screws, two (2) on each side of the bracket into the wall studs as shown below. Diagram 6 -Final Install Diagram 3 -Bracket screw locations. Regency HZ33CE Gas Fireplace...
  • Page 49: Optional Mantel Installation

    Diagram 2 -Bracket screw locations on unit. 2. Install four (4) wood screws, two (2) on each side of the bracket into the wall studs as shown below. Diagram 3 -Bracket screw locations into stud. Diagram 6 -Final Install Regency HZ33CE Gas Fireplace...
  • Page 50: Operating Instructions

    fi lm will bake on and become very diffi cult to remove. Use a non-abrasive cleaner and DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS HOT. Regency HZ33CE Gas Fireplace...
  • Page 51: Copy Of Lighting Plate Instructions

    If service is to be performed - you must disconnect power to the unit, from the battery pack, refer to manual. Appuyez sur le bouton ON / OFF Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction pour plus de détails. DO NOT REMOVE THIS INSTRUCTION PLATE 918-628b Regency HZ33CE Gas Fireplace...
  • Page 52: Maintenance

    Replacement of the glass panels 8. Verify operation after servicing. should be done by a licensed or qualifi ed service person. Regency HZ33CE Gas Fireplace...
  • Page 53: Valve Tray Replacement

    Diagram 2 1. Install new Valve Tray Assembly. 6. Disconnect the inlet gas line. 2. Reverse steps 8-1. 7. Disconnect the EV1, EV2, and ground wires from the valve - as shown below. Ground Diagram 3 Regency HZ33CE Gas Fireplace...
  • Page 54: Parts List

    **Clean Front Face 437-578 Valve Assembly 433-511 **Firebox Assembly 437-012 Bracket Not a replacement part 437-525 Burner Assembly 911-006 Pilot Assembly - NG 437-510 Glass Tray Assy 911-007 Pilot Assembly - LP 437-004 Pilot Cover 919-120 Manual Regency HZ33CE Gas Fireplace...
  • Page 55: Accessories

    PARTS LIST ACCESSORIES Part # Description 434-044 Enamel Panel Top 434-042 Enamel Panel Left 434-041 Enamel Panel Right 434-043 Enamel Panel Back Regency HZ33CE Gas Fireplace...
  • Page 56 NOTES Regency HZ33CE Gas Fireplace...
  • Page 57 NOTES Regency HZ33CE Gas Fireplace...
  • Page 58 NOTES Regency HZ33CE Gas Fireplace...
  • Page 59: Warranty

    It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. ® The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers.
  • Page 60 ___________________________________________________________________ HZ33CE Video Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency Horizon and SureFire are trademarks of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2013, FPI Fireplace Products International Ltd. All rights reserved.

This manual is also suitable for:

Hz33ce-lp

Table of Contents