Sign In
Upload
Manuals
Brands
Digi Manuals
Control Unit
XTend vB DigiMesh XTP9B-DPM-001
Digi XTend vB DigiMesh XTP9B-DPM-001 Manuals
Manuals and User Guides for Digi XTend vB DigiMesh XTP9B-DPM-001. We have
1
Digi XTend vB DigiMesh XTP9B-DPM-001 manual available for free PDF download: User Manual
Digi XTend vB DigiMesh XTP9B-DPM-001 User Manual (146 pages)
Radio Frequency (RF) Module
Brand:
Digi
| Category:
Control Unit
| Size: 1.5 MB
Table of Contents
Revision History
2
Table of Contents
3
The Xtend Vb RF Module
9
About the Xtend Vb RF Module
9
Xtend Replacement Numbers
9
Certification Overview
9
Technical Specifications
10
General Specifications
10
Performance Specifications
10
Networking Specifications
11
Power Requirements
11
Regulatory Approvals
12
Hardware
13
Connect the Hardware
13
Mechanical Drawings
14
Pin Signals
15
Xtend Vb RF Module Modes
19
Transparent and API Operating Modes
19
Transparent Operating Mode
19
API Operating Mode
19
Receive Mode
20
Transmit Mode
20
Command Mode
21
Enter Command Mode
21
Send at Commands
21
Apply Command Changes
22
Exit Command Mode
22
Operation
23
Serial Interface
23
UART Data Flow
23
Serial Data
24
Flow Control
24
Data in (DIN) Buffer and Flow Control
25
Data out (DO) Buffer and Flow Control
26
Networking Methods
27
The MAC and PHY Layers
27
64-Bit Address
28
Make a Unicast Transmission
28
Delivery Methods
29
Point to Point / Point to Multipoint (P2MP)
29
Repeater / Directed Broadcast
29
Digimesh Networking
30
AT Commands
34
Addressing Commands
34
CI (Cluster ID)
34
DH (Destination Address High)
34
DL (Destination Address Low)
35
NI (Node Identifier)
35
Network Discovery Options)
35
NT (Network Discovery Back-Off)
36
SH (Serial Number High)
36
Serial Number Low)
36
TO (Transmit Options)
37
Command Mode Options
38
CC (Command Sequence Character)
38
CT (Command Mode Timeout)
38
GT (Guard Times)
38
Diagnostic Commands
39
H (MAC Unicast One Hop Time)
39
Board Voltage)
39
MAC Broadcast One Hop Time)
39
BC (Bytes Transmitted)
40
DB (Last Packet RSSI)
40
EA (MAC ACK Failure Count)
40
ER (Receive Count Error)
41
GD (Good Packets Received)
41
R# (Reset Number)
42
TR (Transmission Failure Count)
42
UA (Unicasts Attempted Count)
43
Firmware Commands
43
CK (Configuration CRC)
43
DD (Device Type Identifier)
43
NP (Maximum Packet Payload Bytes)
44
HV (Hardware Version)
44
VR (Firmware Version)
44
I/O Settings Commands
44
CD (GP02 Configuration)
44
CS (GP01 Configuration)
45
RP (RSSI PWM Timer)
46
RT (GPI1 Configuration)
47
I/O Diagnostic Commands
47
TP (Board Temperature)
47
MAC/PHY Commands
47
HP (Preamble ID)
48
ID (Network ID)
48
MT (Broadcast Multi-Transmits)
48
TX Power Level)
48
RR (Unicast Retries)
49
Network Commands
49
BH (Broadcast Hops)
49
CE (Routing / Messaging Mode)
50
MR (Mesh Unicast Retries)
50
NH (Network Hops)
51
NN (Network Delay Slots)
51
Security Commands
51
EE (Encryption Enable)
51
KY (AES Encryption Key)
52
Serial Interfacing Commands
52
AO (API Options)
52
AP (API Enable)
53
BD (Baud Rate)
53
FT (Flow Control Threshold)
55
NB (Parity)
55
RB (Packetization Threshold)
55
Packetization Timeout)
56
SB (Stop Bits)
57
Xtend Vb RF Modulespecial Commands
57
AC (Apply Changes)
57
CN (Exit Command Mode)
57
Software Reset)
58
RE (Restore Defaults)
58
WR (Write)
58
R1 (Restored Compiled)
58
Operate in API Mode
60
API Mode Overview
60
API Frame Specifications
60
Calculate and Verify Checksums
62
Escaped Characters in API Frames
62
API Frames
63
API Frame Exchanges
64
Code to Support Future API Frames
65
AT Command Frame 0X08
66
AT Command - Queue Parameter Value Frame 0X09
67
Legacy TX Request Frame 0X00
69
Transmit Request Frame 0X10
71
Explicit Addressing Command Frame 0X11
74
Remote at Command Request Frame 0X17
78
AT Command Response Frame 0X88
81
Modem Status Frame 0X8A
82
Transmit Status Frame 0X8B
83
Legacy TX Status Frame 0X89
85
Route Information Packet 0X8D
86
Aggregate Addressing Update Frame 0X8E
91
Legacy RX Indicator Frame 0X80
93
RX Indicator Frame 0X90
96
Explicit Rx Indicator Frame 0X91
98
Node Identification Indicator Frame 0X95
101
Remote Command Response Frame 0X97
105
Work with Networked Devices
108
Network Commissioning and Diagnostics
108
Configure Devices
108
Configure a Device Remotely
108
Send a Remote Command
108
Apply Changes on Remote Devices
109
Remote Command Response
109
Establish and Maintain Network Links
109
Build Aggregate Routes
109
Examples
110
Replace Nodes
111
Test Links in a Network
111
Test Links between Adjacent Devices
112
Example
114
RSSI Indicators
114
Discover Devices
115
Trace Route Option
116
NACK Messages
117
Certifications
118
FCC (United States)
118
OEM Labeling Requirements
118
FCC Notices
118
FCC Antenna Certifications
119
Antenna Options
120
Industry Canada (IC)
127
Labeling Requirements
127
Transmitters for Detachable Antennas
128
Detachable Antennas
128
ACMA (Australia)
128
Power Requirements
128
Development Kit
130
Development Kit Contents
130
Interface Hardware
131
XTIB-R RS-232/485 Interface Board
132
Configuration Switch
133
I/O and Power Leds
133
Serial Port
133
RSSI Leds
133
Power Connector
134
XTIB-R Dip Switch
134
Adapters
135
NULL Modem Adapter (Male-To-Male)
135
NULL Modem Adapter (Female-To-Female)
135
Serial Loopback Adapter
136
Male DB-9 to RJ-45 Adapter
136
Female DB-9 to RJ-45 Adapter
137
Interface Protocols
137
RS-232 Operation
137
RS-485 (2-Wire) Operation
141
RS-485 (4-Wire) and RS-422 Operation
143
Advertisement
Advertisement
Related Products
Digi XTend vB DigiMesh XTP9B-DPS-001
Digi XTend vB DigiMesh XTP9B-DMM-001
Digi XTend vB DigiMesh XTP9B-DMS-001
Digi XT09-MI
Digi XT09-SI
Digi XT09-MI-MESH
Digi XT09-SI-MESH
Digi XTend vB DigiMesh
Digi XTend
Digi XKB9-DMT-UHP
Digi Categories
Network Router
Control Unit
Modem
Gateway
Server
More Digi Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL