Digi XTend vB DigiMesh Manuals

Manuals and User Guides for Digi XTend vB DigiMesh. We have 1 Digi XTend vB DigiMesh manual available for free PDF download: User Manual

Digi XTend vB DigiMesh User Manual

Digi XTend vB DigiMesh User Manual (135 pages)

Radio Frequency (RF) Module

Brand: Digi | Category: Control Unit | Size: 1 MB

Table of Contents

Table of Contents
4
Xtend Vb Digimesh RF Module User Guide

9
Development Kit

11
- Development Kit Contents
  12
- Interface Hardware
  12
- XTIB-R RS-232/485 Interface Board
  13
  - Configuration Switch
    13
  - I/O and Power Leds
    14
  - Serial Port
    14
  - RSSI Leds
    14
  - Power Connector
    14
  - XTIB-R DIP Switch
    14
- Adapters
  15
- Interface Protocols
  18
Technical Specifications

26
- General Specifications
  27
- Performance Specifications
  27
- Networking Specifications
  27
- Power Requirements
  28
- Regulatory Conformity Summary
  28
Hardware

29
- Connect the Hardware
  30
- Mechanical Drawings
  31
- Pin Signals
  31
Modes

34
- Transparent and API Operating Modes
  35
  - Transparent Operating Mode
    35
  - API Operating Mode
    35
- Receive Mode
  35
- Transmit Mode
  36
- Command Mode
  36
  - Enter Command Mode
    36
  - Troubleshooting
    37
  - Send at Commands
    37
  - Response to at Commands
    38
  - Apply Command Changes
    38
  - Make Command Changes Permanent
    38
  - Exit Command Mode
    38
Operation

39
- Serial Interface
  40
- UART Data Flow
  40
- Serial Data
  40
- Flow Control
  40
  - Data in (DIN) Buffer and Flow Control
    41
  - Data out (DO) Buffer and Flow Control
    42
Networking Methods

44
- The MAC and PHY Layers
  44
- 64-Bit Addresses
  44
- Make a Unicast Transmission
  45
- Delivery Methods
  45
AT Commands

50
- Addressing Commands
  51
  - CI (Cluster ID)
    51
  - DH (Destination Address High)
    51
  - DL (Destination Address Low)
    51
  - NI (Node Identifier)
    51
  - Network Discovery Options)
    52
  - NT (Network Discovery Back-Off)
    52
  - SH (Serial Number High)
    53
  - Serial Number Low)
    53
  - TO (Transmit Options)
    53
- Command Mode Options
  54
  - CC (Command Character)
    54
  - CT (Command Mode Timeout)
    54
  - GT (Guard Times)
    54
- Diagnostic Commands
  55
  - H (MAC Unicast One Hop Time)
    55
  - Board Voltage)
    55
  - MAC Broadcast One Hop Time)
    55
  - BC (Bytes Transmitted)
    55
  - DB (Last Packet RSSI)
    56
  - EA (MAC ACK Failure Count)
    56
  - ER (Receive Count Error)
    56
  - GD (Good Packets Received)
    57
  - RC (RSSI for Channel)
    57
  - R# (Reset Number)
    57
  - TR (Transmission Failure Count)
    58
  - UA (Unicasts Attempted Count)
    58
- Firmware Commands
  58
  - CK (Configuration CRC)
    58
  - DD (Device Type Identifier)
    58
  - NP (Maximum Packet Payload Bytes)
    59
  - HS (Hardware Series)
    59
  - HV (Hardware Version)
    59
  - VR (Firmware Version)
    59
- I/O Settings Commands
  59
  - CD (GP02 Configuration)
    60
  - CS (GP01 Configuration)
    60
  - RP (RSSI PWM Timer)
    60
  - RT (GPI1 Configuration)
    61
- I/O Diagnostic Commands
  61
  - TP (Board Temperature)
    61
- MAC/PHY Commands
  62
  - HP (Preamble ID)
    62
  - ID (Network ID)
    62
  - MT (Broadcast Multi-Transmits)
    62
  - TX Power Level)
    63
  - RR (Unicast Mac Retries)
    63
- Network Commands
  63
  - BH (Broadcast Hops)
    63
  - CE (Routing / Messaging Mode)
    64
  - MR (Mesh Unicast Retries)
    64
  - NH (Network Hops)
    64
  - NN (Network Delay Slots)
    65
- Security Commands
  65
  - EE (Encryption Enable)
    65
  - KY (AES Encryption Key)
    65
- Serial Interfacing Commands
  65
  - AO (API Options)
    66
  - AP (API Enable)
    66
  - BD (Baud Rate)
    66
  - FT (Flow Control Threshold)
    67
  - NB (Parity)
    67
  - RB (Packetization Threshold)
    68
  - Packetization Timeout)
    68
  - SB (Stop Bits)
    69
- Special Commands
  69
  - AC (Apply Changes)
    69
  - CN (Exit Command Mode)
    69
  - Software Reset)
    70
  - RE (Restore Defaults)
    70
  - WR (Write)
    70
  - R1 (Restored Compiled)
    70
Operate in API Mode

71
- API Mode Overview
  72
Apiframes

77
Work with Networked Devices

117
- Network Commissioning and Diagnostics
  117
- Local Configuration
  117
- Remote Configuration
  117
  - Send a Remote Command
    117
  - Apply Changes on Remote Devices
    117
  - Remote Command Response
    117
- Establish and Maintain Network Links
  118
  - Build Aggregate Routes
    118
  - Digimesh Routing Examples
    118
  - Replace Nodes
    119
- Test Links in a Network - Loopback Cluster
  119
- Test Links between Adjacent Devices
  120
  - Example
    121
  - RSSI Indicators
    122
  - Discover All the Devices on a Network
    122
  - Trace Route Option
    123
  - NACK Messages
    124
Regulatory Information

125
- FCC (United States)
  126
  - OEM Labeling Requirements
    126
  - FCC Notices
    126
  - RF Exposure Statement
    127
  - FCC Antenna Certifications
    127
  - Xtend Vb RF Module Antenna Options
    128
  - FCC Publication 996369 Related Information
    133
- ISED (Innovation, Science and Economic Development Canada)
  135
  - Labeling Requirements
    135
  - Transmitters for Detachable Antennas
    135
  - Detachable Antennas
    135

Advertisement

Advertisement

Related Products

Digi Categories

Network Router

Network Router Control Unit Modem Gateway Server

More Digi Manuals