Roban Bell 429 Compactor Manual

Hide thumbs

page of 38

/ 38
Bookmarks

Quick Links

Download this manual

Bel

ll 42

stribut

ted by

CCPM SC

CALE RC H

29™

™

tor

HELICOPT

TER

nual

Need help?

Do you have a question about the Bell 429 Compactor and is the answer not in the manual?

Questions and answers

Summary of Contents for Roban Bell 429 Compactor

Page 1 ll 42 29™ ™ nual stribut ted by CCPM SC CALE RC H HELICOPT TER ...
Page 2 3 ell, emblem ms, logos, a and body d esigns are trademark ks of Textro on Innovat tions c. and are used unde r license b y Roban Lt td. oban Limite ed ryriver Indu ustrial Zone e, Venture Cross Rd. aolian, Wan njiang City District of Dongguan n, 23046 Dong gguan Cou nty (GD) ‐ ‐ PRC yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 3: Specifications
Battery:* 44.4V 5000mAh 35C+ Flight time: 5 minutes Takeoff weight: 9000g Flight Stabilization:* 3 axis flybarless gyro Radio Control:* min. 6 channel with pitch and throttle curves *) Optionally available equipment The Compactor is a high performance radio controlled scale helicopter. Our goal was to create a simple, high performance helicopter, with a minimum of mechanical components and simple maintenance. Please read this user manual carefully, it contains instructions for the correct assembly of the model. Please refer to the web site www.robanmodel.com for updates and other important information. Thank you for your purchase, and have a great time with your Compactor! Roban Limited Copyright@2013 - Roban Limited – All rights reserved...
Page 4: Important Notes
*A radio controlled helicopter must only be used in open spaces without obstacles, and far enough from people to minimize the possibility of accidents or of injury to property or persons. *A radio controlled helicopter can behave in an unexpected manner, causing loss of control of the model, making it very dangerous. *Lack of care with assembly or maintenance can result in an unreliable and dangerous model. *Neither Roban Limited nor its agents have any control over the assembly, maintenance and use of this product. Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release Roban Limited from any responsibility or liability arising from the use of this product. SAFETY GUIDELINES *Fly only in areas dedicated to the use of model helicopters. *Follow all control procedures for the radio frequency system. *It is necessary that you know your radio system well. Check all functions of the transmitter before every flight. *The blades of the model rotate at a very high speed; be aware of the danger they pose and the damage they may cause. *Never fly in the vicinity of other people. NOTES FOR ASSEMBLY Please refer to this manual for assembly instructions for this model. Follow the order of assembly indicated. The instructions are divided into chapters, which are structured in a way that each step is based on the work done in the previous step. Changing the order of assembly may result in additional or unnecessary steps. Use thread lockers and retaining compounds as indicated. In general, each bolt or screw that engages with a metal part requires thread lock. Factory pre‐assembled components have been assembled with all the required thread lock and lubricants, and have passed quality control. It is not necessary to disassemble and re‐assemble them. We do not recommend the use of thin cyanoacrylate glue for surface mount of painted parts. The fumes of the curing glue leave white stains on the clear coat, which are hard to remove. Copyright@2013 - Roban Limited – All rights reserved...
Page 5 2pcs 33 – Anten nna 2pcs 34 – – Antenna 2p 35 – Ante nna 2pcs 6 – Tail suppo yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 6 3pcs 56 – 8 8mm LED ca p 1pc 7 – LED cont troller 1pcs 58 – – Decal set 1 yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 7 DDITIONA AL COMPO ONENTS R REQUIRE D TOOLS, L LUBRICAN NTS, ADH HESIVES *Elec ctric Motor: *Generic plie ers 10S S‐12S – 400‐6 600Kv, *Hexagonal d driver, size 1.5 5, 2, 2.5, 3, 4m mm pin nion shaft diam meter 6mm *4mm T‐Wre ench *Spe eed controller r: *5.5mm Sock ket wrench (fo or M3 nuts) mi nimum 120A to be safe *8mm Hex fo ork wrench (fo or M5 nuts) *Bat tteries: 10‐12S S 4000‐5000m mAh ...
Page 8 Install the fro ont seats as sh hown using ep poxy glue. Install the sto owaway as sho own using epo oxy glue. Insta all the cockpit s levers using g epoxy glue. yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 9 Insta all the seats as s shown with epoxy glue. Install the wi ndshield as sh hown. yright@2013 3 - Roban Lim mited – All rig ghts reserved d...
Page 10 sembly M Mechanics s The mechanics are e almost entir rely preassem mbled and split t up into four sections: roto orhead, main frame, tail fra ame and tail t ube. Prior r to the insta allation into t the scale fuse elage, the me echanics have e to be entire ely assembled d, electronic components installed, adju sted and teste ed. After insta...
Page 11 1=81mm 2=112mm m 3=81 1mm gear red servos. T The multi bla ade rotor he ead can feed back force es that may le ead to failure o of plastic com mponents. yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 12 ep 5 – Adj just swas shplate lin nkages The linkages from m the L‐Levers s to the swash h plate have t to be set a at correct len ngth. Distance es are uniball center to un niball cent er: 1=35mm ep 6 – Mo otor and B Belt insta allation ...
Page 13 Step 7 – Electrical Wiring and Setup The mechanics have to be fully electrically setup and adjusted ATTENTION ! prior to installation into the fuselage. As the use of a 12S (44.4V) setup is necessary, we strongly recommend to run the When using the a pitch gauge to adjust correct CP travels, control equipment on a separate 2S Lipo battery and BEC for make sure that the gauge lines up with the flat surface of security reasons. ...
Page 14 ep 8 – Inst tallation of mecha anics unt the four L L‐brackets (60 0UH1‐003) on nto both side es of Unmount the e entire tail ro otor frame fr rom the tail b box again. the main frame as shown. M Make sure t hey ...
Page 15 9) as Use screws (40) an nd washers (4 41) to install t he tail tube. shown. yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 16 the fuselage. Insta all the wings u using epoxy gl ue Insta all the top hat tch. Install the rot tor head. yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 17 Insta all antennas (3 31) as shown. Install antenn na as shown Insta all windshield wipers as sho own Install antenn na as shown. Connect the L LED controller r to the LED li ghts. Insta all antennas a s shown. ...
Page 18 yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 19 A – Explos sion Draw wings yright@2013 3 - Roban Lim mited – All rig ghts reserved...
Page 27 yright@2013 3 - Roban Lim m ited – All rig g hts reserved d...
Page 28 – Sparep parts yright@2013 3 - Roban Lim mited – All rig ghts reserved d...
Page 32 yright@2013 3 - Roban Lim m ited – All rig g hts reserved d...
Page 33 Taumelscheibe Oberteil 1‐JJ‐70‐00028 Bearing 30x42x7 Kugellager 30x42x7 1‐JJ‐70‐00029 Swash lower ring Taumelscheibe Unterteil 1‐JJ‐70‐00030 Ball head Kugelkopf 1‐JJ‐70‐00031 Washer 2x8x1 Beilagscheibe 2x8x1 1‐JJ‐70‐00032 Screw M2x6 Schraube M2x6 RCH‐70‐022 1‐JJ‐70‐00003 Rotorhead top Rotorkopf oben 1‐JJ‐70‐00004 Rotorhead bottom Rotorkopf unten RCH‐70‐023 1‐JJ‐70‐00001 Rotorhead Cap Rotorkopfkappe RCH‐70‐024 1‐JJ‐70‐00017 Grip Spindle Blattlagerwelle Copyright@2013 - Roban Limited – All rights reserved...
Page 34 X Junction X‐Verbinder 002 RCH‐70‐042 1‐JJ‐70‐00097 Tail servo frame Heckservorahmen 1‐JJ‐70‐00098 Tail servo clamp Heckservoklammer RCH‐70‐043 1‐JJ‐70‐00102 Gear 1M 30T Zahnrad 1M30T RCH‐70‐044 1‐JJ‐70‐00103 Tail pushrod 702mm Gestänge 702mm RCH‐70‐045 1‐JJ‐70‐00104 Tail support holder Strebenaufnahme 1‐JJ‐70‐00105 Bolt 1.5x7.8 Bolzen 1.5x7.8 1‐JJ‐70‐00106 Tail support rod Heckstrebe RCH‐70‐046 11‐600UH1‐007 Tail support clamp Heckstrebenklammer Copyright@2013 - Roban Limited – All rights reserved...
Page 35 1‐JJ‐70‐00045 Bearing 5x10x4 Kugellager 5x10x4 RCH‐70‐072 1‐JJ‐70‐00054 Screw M2.5x8 Schraube M2.5x8 RCH‐70‐073 1‐JJ‐70‐00055 Bearing 12x24x6 Kugellager 12x24x6 RCH‐70‐074 1‐JJ‐70‐00056 Bearing 10x19x5 Kugellager 10x19x5 RCH‐70‐075 1‐JJ‐70‐00081 Nylon Nut M2.5 Nylon Mutter M2.5 RCH‐70‐076 1‐JJ‐70‐00084 Screw M2.5x8 Schraube M2.5x8 RCH‐70‐077 1‐JJ‐70‐00085 Screw M2.5x20 Schraube M2.5x20 RCH‐70‐078 1‐JJ‐70‐00086 Screw M3x8 Schraube M3x8 Copyright@2013 - Roban Limited – All rights reserved...
Page 36 RCH‐70‐105 1‐60‐WJ‐00004 Shaft bevel gear Kegelrad 20T RCH‐70‐106 1‐JJ‐70‐00089 Washer 10x13x0.1 Beilagscheibe 10x13x0.1 RCH‐70‐107 1‐JJ‐70‐00129 Nylon Nut M2 Nylon Mutter M2 RCH‐70‐108 1‐JJ‐70‐00141 Tail spindle Heckrotor Welle RCH‐70‐109 1‐JX‐47‐00115 Rotor hub 3 blade Rotorkopf 3 Blatt RCH‐70‐110 1‐JX‐47‐00103 Rotor hub 4 blade Rotorkopf 4 Blatt Copyright@2013 - Roban Limited – All rights reserved...

This manual is also suitable for:

Bell 429Compactor bell 429

Roban Bell 429 Compactor Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Roban Bell 429 Compactor

Summary of Contents for Roban Bell 429 Compactor

Page 3: Specifications

Page 4: Important Notes

This manual is also suitable for: