Download Print this page
Roban B429 Instruction Manual

Roban B429 Instruction Manual

Scale fuselage 600 size
Hide thumbs Also See for B429:

Advertisement

Quick Links

Instruction manual
Scale Fuselage B429
600 size
1.
INTRODUCTION
Thank you for buying Roban Model products. The 500 size EC-135 scale fuselage is designed as an easy
to use product. Please read the manual carefully before assembling the model, and follow all
precautions and recommendations located within the manual. Be sure to retain the manual for future
reference, routine maintenance and tuning. The scale fuselage is designed for T-REX 500 Helicopter
series use. You can easily put it on your T-REX 500 for new clothing.
Important Note
Roban Model R/C Helicopters are advanced, high-performance devices, built incorporating the latest
technologies. They are not intended as toys, and improper use can potentially lead to serious injury, or
even fatal accidents. We implore you to read this manual thoroughly before operating these models.
Safety should be your utmost priority - not just your own, but also that of others and your surroundings
when piloting Roban Model products.
Liability Disclaimer:
The manufacturer and the seller cannot accept liability for the operation or misuse of this product.
Roban Model R/C helicopters are intended to be used exclusively by experienced adults in legally
sanctioned flying fields. Once sold, we cannot monitor or control the product's operation or usage.
Operation Guidelines:
Upon assembly of the scale fuselage, the weight and complexity of the structure will increase. To
mitigate risk of accidents and damages, we advise against attempting 3D flights.
Skill Requirements:
The operation of R/C products necessitates a certain level of skill and familiarity. Any damages or
dissatisfaction resulting from accidents, modifications, or operational mishaps are not covered under
any warranty. Consequently, such products cannot be returned for repair or if you experience problems
during operation or maintenance.

Advertisement

loading
Need help?

Need help?

Do you have a question about the B429 and is the answer not in the manual?

Questions and answers

Summary of Contents for Roban B429

  • Page 1 600 size INTRODUCTION Thank you for buying Roban Model products. The 500 size EC-135 scale fuselage is designed as an easy to use product. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manual for future reference, routine maintenance and tuning.
  • Page 2 OPERATIONAL GUIDELINES FOR SAFETY IN USING R/C AIRCRAFT MODELS Safety Zone: Prioritize the safety of others by operating R/C aircraft models in isolated areas, free of bystanders. Avoid piloting these models near residential zones or large groups of people. Operational Risks: Be aware that R/C aircraft models are susceptible to accidents, malfunctions, and crashes.
  • Page 3: Contents Of Kit

    CONTENTS OF KIT SCOPE OF DELIVERY 1. Cockpit 2. Pilot Seats x2 3. Seat Holder x2 4. Pitch Stick x2 5. Cyclic Stick x2 6. Foot Pedal x4 7. Landing gear x2 8. Foot Steps x2 9. Screw A3x24 x4 10.
  • Page 4 16. Antenna x2 17. Antenna 18. Pitot Tube x2 19. Tail Distancer x2 20. Screw M3x20 x2 21. Screw M3x14 x2 22. Screw A1.7x6 x6 23. Screw A2x8 x4 24. Screw A3x14 x4 25. Screw A2x12 x4 26. Tail Distancer Rubber 27.
  • Page 5 34. Wooden Nuts x6 35. Screw M2x8 x6 36. Mounting blocks x2 37. Wooden Washers x3 38. Washer M3 x4 Decal Set PVC Disc REQUIRED TOOLS / CONSUMABLES Tool No. Tool/Consumable Hobby knife Allen wrench Phillips screwdriver File Side cutters Silicone adhesive Super glue 2K Epoxy glue...
  • Page 6: Installation

    4. INSTALLATION 4.1. Remove the engine nacelle as shown by removing the screws. 4.2. Insert the landing gears (7) and secure them with screws (9) inside the fuselage.
  • Page 7 4.3. Glue the footrests (8) into the fuselage as shown with expoxide glue. 4.4. Glue the cockpit (1) with epoxide glue into the floorboard as shown.
  • Page 8 4.5. Glue the pedals (3), footrests (6), cyclic sticks (5) and the pitch stick(4) into floorboard as shown with epoxide glue.
  • Page 9 4.6. Glue the seats (2) and the with the seat holders (3) into the floorboard as shown with epoxide glue. 4.7. Mount the holders (36) to the mechanic as shown. Do test fly your mechanic before installing it into the fuselage with a 3D landing gear.
  • Page 10 4.8. Remove the tail rotor prior to assembly. 4.9. Insert the mechanic as shown into the fuselage.
  • Page 11 4.10. Add the dampening rubber to the tail boom as shown. 4.11. Install the red LED (32) inside the socket (30) as show with glue. Route the wires through the tail fin center hole.
  • Page 12 4.12. Glue the tail distancer (19) into the fin with epoxide glue. 4.13. Attach the tail fin (10) to the tail boom with screws (24) as shown. Then route the LED wire through the boom towards the front of the fuselage.
  • Page 13 4.14. Shove the tail onto the mechanics tail boom as shown. 4.15. Attach the supplied L-Lever (27) onto the tail rotor unit as shown. Then attach onto the tail boom, tighten screws and attach all linkages.
  • Page 14 4.16. Screw the tail tube to the fuselage using washer (34) and screw (35). First, drill evenly distributed 1.5mm holes through the tube and fuselage. Then glue the captive nuts inside the fuselage using plywood washers. Ensure that no glue enters the threads. Tighten the screws slightly before the glue hardens, correctly align the tail tube, and secure it with tape until the glue fully cures.
  • Page 15 4.18. Install the green LED (29) on the right, and the red LED left tail wing (28) as shown, if you stand behind the helicopter facing away from you. 4.19. Glue the tail units carefully into the tail boom using epoxide glue. Secure them with tape while the adhesive cures.
  • Page 16 4.20. Then screw down the mechanics into the fuselage at the four points as shown. 4.21. Mount the engine cover again with screws, then mount the rotor head.
  • Page 17: Spare Part List

    4.22. Finally glue all scale parts (14-18) as shown into the fuselage. 5. SPAREPART LIST 600 Bell 600 贝尔 429 B429PJ001 429 front 前窗 window 600 Bell 600 贝尔 429 B429PJ002 429 all 全套窗 windows 600 Bell 600 贝尔 429 B429PJ003 429 landing 脚架...
  • Page 18 600 Bell 600 贝尔 429 B429PJ004 429 foot 脚踏 steps 600 Bell 600 贝尔 429 B429PJ005 429 antenna 像真件 600 Bell 600 贝尔 429 B429PJ006 429 tail 平垂尾 wings 600 Bell 600 贝尔 429 B429PJ007 固定件 mounting hardware 600 Bell 600 贝尔...
  • Page 19 6. ILLUSTRATION OF READY MOUNTED HELICOPTER Specifications: Length: 1470mm Height: 400mm Width: 320mm Weight: 1200g Suitable for Align TREX560 und similar mechanics We wish you a lot of fun with the fuselage! Copyright 2024 – www.robanmodel.com...

This manual is also suitable for:

Ec-135