Roban Bell 407 Instruction Manual
  1. Manuals
  2. Brands
  3. Roban Manuals
  4. Toy
  5. Bell 407
  6. Instruction manual

Roban Bell 407 Instruction Manual

True scale
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL

Bell 407
True Scale
1/13 CCPM OUTDOOR RC HELICOPTER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Bell 407 and is the answer not in the manual?

Questions and answers

Related Manuals for Roban Bell 407

Summary of Contents for Roban Bell 407

  • Page 1: Instruction Manual

    INSTRUCTION MANUAL Bell 407 True Scale 1/13 CCPM OUTDOOR RC HELICOPTER...

  • Page 2: Specifications

    Roban Bell 407 is intended for intermediate helicopter pilots. And although the Roban Bell 407 is easy to control right out of the box, please take the time to read through this manual completely in order to assure you are getting the maximum out of this stunning and technically top edge product.
  • Page 3 -Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose. -Never lick or place any portion of your Roban Bell 407 in your mouth as it could cause serious injury or even death.
  • Page 4 True Scale Bell 407 Instruction Manual Scale accessories and installation accessories Decals Instruction Manual Required Consumables: Blue thread lock Red thread lock 30 minute epoxy CA or Super Glue Foam backed tape Zip ties Tape Tools: Hobby knife Hex screw driver set...

  • Page 5: Section A - Mechanic Assembly

    True Scale Bell 407 Instruction Manual SECTION A – MECHANIC ASSEMBLY NOTE: As with any RC model helicopter, all fasteners installed into metal parts must use blue thread lock and all bearings installed into metal bearing blocks must use red bearing lock, wipe off excess.
  • Page 6 True Scale Bell 407 Instruction Manual b) Remove the screws as shown from the tail frame and remove the tail frame as shown including the bearing. Disconnect the servo linkage. Then push the other bearing in the frame out of its block, only this way you can release the tail belts tension. Remove belt from pulley.

  • Page 7: Section B - Installation Of Electronic Components

    True Scale Bell 407 Instruction Manual SECTION B – INSTALLATION OF ELECTRONIC COMPONENTS 1) Install Motor a) Install Pinion gear on motor. Eventually add a flat with a file to the motor shaft for security where the grub screw engages the shaft. Make sure the pinion gear is installed at the appropriate height to fully engage the main gear.

  • Page 8: Section C - Adjustments And Electronic Setup

    True Scale Bell 407 Instruction Manual b) Connect the Gyro to the RX following the gyro instruction manual. 5) Install ESC a) Solder the supplied battery connector prolonging wire to the ESC. b) Connect the motor to the ESC c) Connect ESC to RX.

  • Page 9: Section D - Installation Into The Fuselage

    Please be advised that the swash plate is a 140deg and not a 120deg CCPM. b) If using the Roban 3 axis gyro, please use the following parameters (online) 4) Test TX a) In order to test your TX and the proper setup, please follow your radio controls user manual.

  • Page 10: Section E - Final Adjustments

    True Scale Bell 407 Instruction Manual b) Arrange all wires properly, make sure that the motor hatch can enclose all electronic parts without problems. 3) Securing Cables and Wires a) The helicopter´s mechanics are built very compact. It is necessary that you make sure that all wires and cables are locked in secure spaces using zip ties or spiral cords.
  • Page 11 True Scale Bell 407 Instruction Manual EXHIBIT A – MECHANICAL ASSEMBLY NOTE: As the helicopter is readily assembled the following explosion drawings are a guide to the according spare part numbers, but also a guide on how to setup the mechanics.
  • Page 12 True Scale Bell 407 Instruction Manual 3) Rotor head 1-JX-47-00104 1-JX-47-00130 1-JX-47-00109 1-JX-47-00122 1-JX-47-00102 1-JX-47-00106 1-JX-47-00112 1-JX-47-00106 1-JX-47-00108 1-JX-47-00107 1-JX-47-00109 1-JX-47-00110 1-JX-47-00105 1-JX-47-00113 4) Main Shaft 1-JX-47-00006 1-JX-47-00007 1-JX-47-00005...
  • Page 13 True Scale Bell 407 Instruction Manual 5) Complete CCPM assy 1-JX-47-00001 1-JX-47-00000 1-JX-47-00000 1-JX-47-00114 1-JX-47-00000 1-JX-47-00051 6) Main Frame 1-JX-47-00002 1-JX-47-00000 1-JX-47-00001 1-JX-47-00003...
  • Page 14 True Scale Bell 407 Instruction Manual 7) Front servo holder 1-JX-47-00058 1-JX-47-00057 1-JX-47-00059 1-JX-47-00054 8) Servo levers 1-JX-47-00013 1-JX-47-00027 1-JX-47-00057 1-JX-47-00014 1-JX-47-00028 1-JX-47-00055...
  • Page 15 True Scale Bell 407 Instruction Manual 9) Front Servo Assy 1-JX-47-00000 1-JX-47-00025 1-JX-47-00024 1-JX-47-00060 1-JX-47-00062 1-JX-47-00014 1-JX-47-00063 1-JX-47-00015 1-JX-47-00014 1-JX-47-00049 10) Tail gearbox frame 1-JX-47-00046 1-JX-47-00045...
  • Page 16 True Scale Bell 407 Instruction Manual 11) Aft servo holder 1-JX-47-00053 1-JX-47-00054 12) Aft servo assy 1-JX-47-00000 1-JX-47-00052 1-JX-47-00054 1-JX-47-00015 1-JX-47-00007...
  • Page 17 True Scale Bell 407 Instruction Manual 13) Tail boom holder assy 1-JX-47-00010 1-JX-47-00032 1-JX-47-00065 1-JX-47-00038 1-JX-47-00075 - 1-JX-47-00040 1-JX-47-00007 1-JX-47-00069 1-JX-47-00064 1-JX-47-00072 1-JX-47-00007 1-JX-47-00066 14) Tail servo and main gear assy 1-JX-47-00032 1-JX-47-00033 1-JX-47-00054 1-JX-47-00037 1-JX-47-00030 1-JX-47-00034 1-JX-47-00050 1-JX-47-00036 1-JX-47-00037...
  • Page 18 True Scale Bell 407 Instruction Manual 15) Main gear assy 1-JX-47-00004 1-JX-47-00010 1-JX-47-00009 16) Mounting the main frame 1-JX-47-00048...
  • Page 19 True Scale Bell 407 Instruction Manual 17) Tail frame assy 1-JX-47-00030 1-JX-47-00080 1-JX-47-00082 1-JX-47-00032 1-JX-47-00026 1-JX-47-00077 1-JX-47-00030 1-JX-47-00076 1-JX-47-00078 1-JX-47-00083 1-JX-47-00032 18) Tail rotor assy 1-JX-47-00089 1-JX-47-00088 1-JX-47-00087 1-JX-47-00054 1-JX-47-00100 1-JX-47-00027 1-JX-47-00090 1-JX-47-00099 1-JX-47-00085 1-JX-47-00096 1-JX-47-00086 1-JX-47-00095 1-JX-47-00091 1-JX-47-00097 1-JX-47-00084...
  • Page 20 True Scale Bell 407 Instruction Manual 19) Complete mechanics...
  • Page 21 True Scale Bell 407 Instruction Manual EXHIBIT B SPAREPART LIST SPAREPART SPAREPART SPAREPART NO NAME PART NO DESCRIPTION NAME GERMAN RCH-BE407-001 SWASH HUB TAUMELSCHEIBEN- 1-JX-47-00019 Swash drive MITNEHMER 1-JX-47-00020 Threaded sleeve M3 f. -016 1-JX-47-00022 Drive Arm 1-JX-47-00023 Drive Link 1-JX-47-00024 Sleeve 2x2.78x5...
  • Page 22 True Scale Bell 407 Instruction Manual 1-JX-47-00044 Screw M3x6 PH RCH-BE407-005 PINION GEAR Motorritzel 1-JX-47-00043 Pinion gear 12T 47C-042 Set Screw M3x3 Cyclic Metal Taumescheiben- RCH-BE407-007 1-JX-47-00049 Cyclic Servo 9g Gear Servo# Metallgetriebeservos RCH-BE407-008 Tail Servo Heck Servo 1-JX-47-00050 Tail Servo 9g...
  • Page 23 True Scale Bell 407 Instruction Manual 1-JX-47-00064 Lower tail boom holder 1-JX-47-00065 Upper tail boom holder 1-JX-47-00066 Screw M2x16 SH 1-JX-47-00010 Self locking Nut M2 RCH-BE407-017 Tail boom set Heckrohr Satz 1-JX-47-00014 Ball link 1-JX-47-00015 Screw M2x7 CS 1-JX-47-00061 Push rod sleeve...
  • Page 24 True Scale Bell 407 Instruction Manual 1-JX-47-00087 Screw M2x6 1-JX-47-00115 Screw M2x9 1-JX-47-00092 Tail pitch lever 1-JX-47-00093 Sleeve 2x3.8x2.8 1-JX-47-00094 Sleeve 2x3x0.5 1-JX-47-00014 Ball link 1-JX-47-00015 Screw M2x7 CS 1-JX-47-00095 Tail pitch drive 1-JX-47-00096 Bearing 4x7x2.5 1-JX-47-00097 Control washer 4x6x0.55...
  • Page 25 True Scale Bell 407 Instruction Manual 3Axis HH RCH-BE407-028 3 Achs Gyro 1-JX-47-00068 3 axis gyro Gyro RCH-BE407-029 6S ESC 6S ESC 1-JX-47-00126 ESC 6S 40A RCH-BE407-030 Position light Positionslichter-satz 1-JK-47-00082 Red Light Cap 1-JK-47-00083 Red Light Socket 1-JK-47-00084 Round Light Cap...
  • Page 26 True Scale Bell 407 Instruction Manual 1-JK-47-00033 Right upper support 1-JK-47-00034 Lower wire cutter 1-JK-47-00035 Upper wire cutter 1-JK-47-00036 Handle 1-JK-47-00037 Antenna 1-JK-47-00038 Engine exhaust 1-JK-47-00039 Front gear cap 1-JK-47-00040 Aft gear cap 1-JK-47-00041 Scale Detail 1-JK-47-00042 Scale Detail 1-JK-47-00043...

  • Page 27: Wiring Diagram

    LIPO 6S 1200mAh 25C LIPO 6S 1200mAh 25C FULLYMAX RCH-BE407-041 Battery hatch Batteriefachab-deckung 1-JK-47-0136 Battery hatch 12. WIRING DIAGRAM Note: This is how to wire the Roban 3 Axis Gyro. Other systems may require different wiring setup. 13. SPAREPART PICTURES...
  • Page 28 True Scale Bell 407 Instruction Manual...
  • Page 29 True Scale Bell 407 Instruction Manual Copyright 2012 Roban Limited – www.robanmodel.com...

Table of Contents