— at the click of a button — without interrupting your workflow. A good investment Using power-efficient LED backlights, Nio 3MP LED Display is as low in power consumption as it is high in brightness. Because it uses less power, the display produces less heat and requires less cooling, which impacts maintenance and operational costs.
Steady amber: Display switched off via the standby key, or display in hibernate mode (requires DPMS mode and Hibernate to be enabled in the OSD menu, see “DPMS mode”, page 23 and “Hibernate”, page 24) Front sensor K5902114 /03 Nio 3MP LED Display...
Page 8
If insufficient USB resources are available on the PC, the USB cable may be left unattached and the display will communicate essential QC information using DDC on the video cable, albeit more slowly; USB peripherals will also be ignored. K5902114 /03 Nio 3MP LED Display...
Installation Prior to installing your Nio 3MP LED Display and connecting all necessary cables, make sure to have a suitable display controller physically installed in your computer. If you are using a Barco display controller, please consult the user guide delivered with it to do this.
Image 2-2 WARNING: The display must be in its highest position before it can be properly pivoted. Store the foot lock clip in the storage hole in case the display needs to be transported later. K5902114 /03 Nio 3MP LED Display...
Connect the workstation's USB host to the USB upstream connector on the display if you want to make use of QAWeb or any of the display USB downstream connectors (e.g. to connect a keyboard, mouse, touch pad or other peripheral). K5902114 /03 Nio 3MP LED Display...
Page 12
Image 2-8 Close the connector compartment cover. You will hear a “click” sound when the cover is in position. K5902114 /03 Nio 3MP LED Display...
Put the display in the lowest position and lock the height mechanism. Image 2-10 Put the display face down on a clean and soft surface. Be careful not to damage the panel screen. Remove the plastic cover with a flathead screw driver. K5902114 /03 Nio 3MP LED Display...
2.4 First time starting up Overview You are now ready to start up your Nio 3MP LED Display for the first time. Switch on your Nio 3MP LED Display as described in “Standby switching”, page 19. Turn on the computer connected to your display.
Page 15
Your Nio 3MP LED Display will be running in a basic video mode at a default refresh rate when first time starting up. If you are using a Barco display controller, please consult the user guide delivered with it to install the drivers, software and documentation.
Page 16
Installation K5902114 /03 Nio 3MP LED Display...
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels.
How to bring up the OSD menus The OSD menu allows you to configure different settings to make your Nio 3MP LED Display fit your needs within your working environment. Also, you can retrieve general information about your display and its current configuration settings through the OSD menu.
Page 20
Exit all OSD menus at once by touching the standby key for approximately 2 seconds. The key icons are displayed above the keys, adapted to the function that it is used for (menu dependent). Overview key icons Left, Right Menu Enter Cancel Standby (IEC 60417–5009) K5902114 /03 Nio 3MP LED Display...
About the OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages available for the OSD menu of your Nio 3MP LED Display. To change the language of the OSD menu: Bring up the OSD main menu.
About the power lock function By enabling the power lock function, the Nio 3MP LED Display is forced to remain switched on. This means that it can’t be switched to stand-by mode manually until the power lock function is disabled again.
4.8 Luminance target About the luminance target The luminance target of your Nio 3MP LED Display is adjustable over a predefined range. When you change the luminance target, the display will adjust its backlight to reach the target. To set the luminance target: Bring up the OSD main menu.
To quickly switch the viewing mode without having to enter the OSD menu, touch the left and right key at the same time during normal operation. The diagnostic mode should always be selected when the Nio 3MP LED Display is intended to be used in a diagnostic environment.
The American Association of Physicists in Medicine (AAPM) composed a list of pre-defined reading rooms. Each of these reading rooms are defined by following parameters: • the maximum light allowed in this type of room • the preset ambient light correction value for this reading room K5902114 /03 Nio 3MP LED Display...
Embedded QA is not a replacement for the Barco MediCal QAWeb solution. Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still highly recommends MediCal QAWeb as the solution of choice for calibration and QA. Medical QAWeb brings...
Pressing a key during the compliance check will abort the check. 4.14.4 DICOM calibration About DICOM calibration The DICOM calibration will add a correction to the current DICOM curve to approach the perfect DICOM curve as well as possible. K5902114 /03 Nio 3MP LED Display...
This may be especially useful when operating your display with the screen facing upwards. To set the Display orientation Bring up the OSD main menu. Navigate to the Configuration > Image Sources menu. Enter the Display Orientation submenu. K5902114 /03 Nio 3MP LED Display...
4.18 EDID format About EDID format Your Nio 3MP LED Display describes its capabilities to the display controller by means of display identification data. This data contains timings, display size, pixel mapping info, etc. and is needed to make sure that the video source can be correctly displayed.
(display function, luminance, ALC, etc.) and the status about activated connections. To retrieve the status of your display: Bring up the OSD main menu. Navigate to the Status menu. Enter the Display, Image Sources or Calibration submenu as desired. K5902114 /03 Nio 3MP LED Display...
Page 32
Advanced operation K5902114 /03 Nio 3MP LED Display...
Repacking your display 5.1 Repackaging instructions Overview of the packaging Image 5-1 Video and power cables Display controller box System CD('s) and user guide Power supply Top buffer Display Bottom buffer K5902114 /03 Nio 3MP LED Display...
Page 35
When applicable, put the display controller box in the dedicated cavity of the top buffer. Put the system CD('s) and user guide in their original bag and place it in the dedicated cavity of the top buffer. Close and seal the box. K5902114 /03 Nio 3MP LED Display...
Page 36
Repacking your display K5902114 /03 Nio 3MP LED Display...
LCD. CAUTION: Do not apply or spray liquid directly to the display as excess liquid may cause damage to internal electronics. Instead, apply the liquid to a cleaning cloth. K5902114 /03 Nio 3MP LED Display...
The installer shall assess the magnetic environment before installation or use of the device. Power cords: • Do not overload wall outlets and extension cords as this may result in fire or electric shock. K5902114 /03 Nio 3MP LED Display...
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. K5902114 /03 Nio 3MP LED Display...
Page 42
Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
7.3 Regulatory compliance information Indications for use The Nio 3MP LED Display is intended to be used as a tool in displaying and viewing digital images (excluding digital mammography) for review and analysis by trained medical practitioners. Caution (USA): Federal law restricts this device to sale by or on the order of a physician.
WARNING: Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the Nio 3MP LED Display, including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.
Page 45
GMRS 460, FM ± 5 kHz FRS 460 deviation 1 kHz sine 704 – 787 LTE Band Pulse 13, 17 modulation 217 Hz Nio 3MP LED Display doesn’t contain susceptible components to magnetic fields K5902114 /03 Nio 3MP LED Display...
Indicates the device is approved according to the UL regulations for Canada and US E352529 Indicates the device is approved according to the UL Demko regulations Indicates the device is approved according to the CCC regulations K5902114 /03 Nio 3MP LED Display...
Page 47
Indicates the device serial number Indicates the device part number or catalogue number Warning: dangerous voltage Caution Consult the operating instructions Values for xx and yy can be found in the technical specifications paragraph. K5902114 /03 Nio 3MP LED Display...
Page 48
Indicates the range of humidity to which the medical device can be safely exposed when being stored. Indicates the range of atmospheric pressure to which the medical device can be safely 106 kPa exposed when being stored. 50 kPa K5902114 /03 Nio 3MP LED Display...
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized.
Page 50
(Russia, Kazakhstan, Belarus, Armenia and Kyrgyzstan) Safety specific: IEC 60950-1:2005 + A1:2009 EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 IEC 60601-1:2005 + A1:2012 EN 60601-1:2006 + A1:2013 + A12:2014 ANSI/AAMI ES 60601-1:2005 + R1:2012 K5902114 /03 Nio 3MP LED Display...
A list of the Open Source Software components used is available in the applicable EULA, through the “My Barco” section of the Barco website or through other (online) means. Copyright on each Open Source Software component belongs to the respective initial copyright holder, each additional contributor and/or their respective assignee(s), as may be identified in the respective Open Source Software documentation, source code, README file, or otherwise.
Page 52
Barco whatsoever. You further acknowledge that any such additions, changes or modifications may impair the ability of Barco – at Barco’s sole discretion - to continue to provide service, warranties, software updates, fixes, maintenance, access or such similar abilities, without any recourse or claim towards Barco whatsoever.
Page 53
Important information K5902114 /03 Nio 3MP LED Display...
Need help?
Do you have a question about the Nio 3MP and is the answer not in the manual?
Questions and answers