Kyocera FS-C5350DN Service Manual page 168

2K8
Connector Pin
YC1 1 ERASEMDR
Connected 2 TNSENM
to the
3 ERASECDR
engine
4 TNSENC
PWB.
5 ERASEYDR
6 TNSENY
7 EECLK
8 GND
9 EEDATA
10 +3.3V1
11 ERASEKDR
12 +3.3V2
13 TNSENK
14 DLPTHERM
YC2 1 EEDATA
Connected 2 ERASEDR
to the drum
3 EECLK
PWB K
4 GND
5 +3.3V1
6 N.C.
7 DA1
8 DA0
YC3 1 GND
Connected 2 ERASEKDR
to the drum
3 N.C.
PWB K
YC4 1 GND
Connected 2 TNSENK
to the devel-
3 +3.3V2
oping PWB
4 TH_DLP
K
YC5 1 EEDATA
Connected 2 ERASEDR
to the drum
3 EECLK
PWB Y
4 GND
5 +3.3V1
6 N.C.
7 DA1
8 DA0
YC6 1 GND
Connected 2 ERASEYDR
to the drum
3 N.C.
PWB Y
YC7 1 GND
Connected 2 TNSENY
to the drum
3 +3.3V2
PWB C
4 N.C.
2-3-12
Signal I/O
I 0/24 V DC
O Analog
I 0/24 V DC
O Analog
I 0/24 V DC
O Analog
I 0/3.3 V DC (pulse) EEPROM clock signal
- -
I/O 0/3.3 V DC (pulse) EEPROM data signal
I 3.3 V DC
I 0/24 V DC
I 3.3 V DC
O Analog
O Analog
I/O 0/3.3 V DC (pulse) EEPROM data signal
O 0/24 V DC
O 0/3.3 V DC (pulse) EEPROM clock signal
- -
O 3.3 V DC
- -
O 0/3.3 V DC
O 0/3.3 V DC
- -
O 0/24 V DC
- -
- -
I Analog
O 3.3 V DC
I Analog
I/O 0/3.3 V DC (pulse) EEPROM data signal
O 0/24 V DC
O 0/3.3 V DC (pulse) EEPROM clock signal
- -
O 3.3 V DC
- -
O 0/3.3 V DC
O 0/3.3 V DC
- -
O 0/24 V DC
- -
- -
I Analog
O 3.3 V DC
- -
Voltage
Eraser lamp M: On/Off
Toner sensor M detection voltage
Eraser lamp C: On/Off
Toner sensor C detection voltage
Eraser lamp Y: On/Off
Toner sensor Y detection voltage
Ground
3.3 V DC power source
Eraser lamp K: On/Off
3.3 V DC power source
Toner sensor K detection voltage
Developing thermistor detection voltage
Eraser lamp K: On/Off
Ground
3.3 V DC power source
Not used
Data address signal
Data address signal
Ground
Eraser lamp K: On/Off
Not used
Ground
Toner sensor K detection voltage
3.3 V DC power source
Developing thermistor detection voltage
Eraser lamp Y: On/Off
Ground
3.3 V DC power source
Not used
Data address signal
Data address signal
Ground
Eraser lamp Y: On/Off
Not used
Ground
Toner sensor Y detection voltage
3.3 V DC power source
Not used
Description