Page 1
FabiaTech Corporation IPC Solution Website: http:// www.fabiatech.com Email: support@fabiatech.com Small Cube System Fanless Series FX5653 User’s Manual MAY 2013 Version: 1.1 Part Number: FX5653...
Page 2
FabiaTech shall not be reliable for technical or editorial errors or omissions, which may occur in this document. FabiaTech shall not be reliable for any indirect, special, incidental or consequential damages resulting from the furnishing, performance, or use of this document.
Audio, and two So-DIMM socket supports up to 4GB DDR3 RAM, and a VGA controller. Each FX5653 has four ports for I/O communications. Four RS-232C ports are available. The FX5653 is perfect for communication and small Embedded Control. The unit is only 180 mm (D) X 250 mm (W) X 50 mm (H).
FabiaTech Corporation Series Comparison Table Model FX5653 Processor Intel ® Atom™ D2550 1.86GHz S-Chipset NM10 Memory DDR3-800/1066 204-Pin So-DIMM Storage One CFast, SD and One SATA HDD Display (Dual-Display) VGA, HDMI, DP Watchdog Timer Multi I/O Four R232 USB 2.0 Port...
FabiaTech Corporation Specifications Processor Board – Intel ® Atom™ D2550 Dual Core (1M L2 Cache, 1.86GHz) Low Power Processor with 4GB DDR3-RAM. I/O Outlets – Two 10/100/1000 base-TX Ethernet LAN ports with RJ45. Four RS-232 serial ports with DB9 .
Verify the accessories in the package according to the packing list and see if there is anything missing or incorrect package is included. • If the cable(s) you use to install the FX5653 is not supplied from us, please make sure the specification of the cable(s) is compatible with the FX5653 system.
FabiaTech Corporation Chapter 2 Hardware Installation This chapter introduces the system connectors & jumper settings, and guides you to apply them for field application. Before Installation Before you install the system, make sure you follow the following descriptions. 1. Before removing the cover, shut down the operation System and disconnect power switch to off and unplug AC-to DC Adapter cable.
If you are installing hardware option, you can remove the bottom cover. The following figure will guide you how to install 2.5" HDD, CFast modules, and DDR3 RAM module to FX5653 and how to install the FX5653 fixers. (Please see the spots circled.) a.
Page 12
You may extend additional PCIe Mini Card module to FX5653. Connect the antenna cable from backside antenna hole to GPRS or Wireless LAN module. See as following figure. Note: FX5653 provides two PCIe Mini Card socket, one full size and one half size, half size socket can’t support GPRS module.
Page 13
FabiaTech Corporation d1. Installing half size mini Card module kit (Optional) e. Installing CFast, SD and SIM Card Note: When installing PCIe GPRS Mini card on FX5653 system, also need the installing the SIM Card to system board.
Page 14
FabiaTech Corporation g. Installing the universal fixers on FX5653 Please refer to the down side figure for installing the FX5653 with universal fixers. g1. FX5504K1- Panel Mount (VESA 75*75/100*100) M3*P0.5 g2. FX5501K1- Wall Mount M3*P0.5...
CFAST STANDBY LINK STANDBY LINK I/O peripheral connectors View from the back side, If you are connecting the monitor, LAN, audio, COM and USB to the FX5653. See following figure and a side pictures. ANTENNA LAN1 COM2 COM1 HDMI DISPLAY...
Page 17
HDMI and Dsiplay port Display Port connector HDMI connector Note: The FX5653 don’t support dual display in boot DOS mode. and don’t recommend connecting three tpye monitors at the same time. COM ports The DB9 (COM1~COM4) is standard serials port connector. The following tables show the signal connections of these connectors.
FabiaTech Corporation USB Ports The FX5653 supports a five port USB connector. Any USB device can be attached to USB ports with plug-and-play supported. USB#1~5 Signal Pin 1 USBV Pin 2 USBD- Pin 3 USBD+ Pin 4 USBG Connecting the Audio Microphone In/ EAR-Phone...
2. Power Button & Reset Push Button: Pushing the Power button once will switch the FX5653 on and off, And Reset push button is switcher for system reset; Push and release the button will cause hard ware reset of FX5653 and restart system booting.
Page 20
FabiaTech Corporation a. JP11, JP12, H_JP5 and H_JP6: COM1 ~ COM4 power source selection The COM1 to COM4 Serial ports provide power source will driver the “RI” signal pin- 9 with DB9 connect, JP11 (COM1) and JP12 (COM2) in the lower position of the daughter board, the settings will need to remove the daughter board.
Page 21
FabiaTech Corporation b. JP4 and H_JP3: Select 3VSB/3.3V voltage for PCIe Mini Card module When installing the PCIe Mini Card module, if not correct working (See a PCIe module card specification pin-24 3.3VAUX.), you can to select 3VSB/3.3V voltage. (Defaulted 1, 2 closed.)
Page 22
FabiaTech Corporation e. H_SW1 and H_J2: Int./Ext. USB select and Internal USB header (2.54mm) You can use H_SW1 set the USB signals connected to the internal or external connector. The H_SW1-4~1 control USB port 4, H_SW1-8~5 control USB port 6, When set to the internal connector, external connector will not be able to use.
FabiaTech Corporation Chapter 3 BIOS Setup This chapter describes the BIOS setup. Overview BIOS are a program located on a Flash memory chip on a circuit board. It is used to initialize and set up the I/O peripherals and interface cards of the system, which includes time, date, hard disk drive, and connected devices such as the video display, diskette drive, USB device, and the keyboard.
Page 24
FabiaTech Corporation BIOS Functions On the menu, you can perform the following functions 1. Main 2. Advanced ACPI Settings CPU Configuration Intel Fast Flash Standby USB Configuration IDE Configuration Super IO Configuration H/W Monitor 3. Chipset Host Bridge South Bridge 4.
FabiaTech Corporation Main Setup This section describes BIOS information and system clock setup. If the CPU board is already installed in a working system, you will not need to select this option anymore. System Date & System Time Setup Highlight the <Date> field and then press the [+]/ [-] keys or enter new values to set the current date.
FabiaTech Corporation Advanced Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Super IO Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>...
FabiaTech Corporation ACPI settings This filed specifies allow you set this value to utilize the ACPI (Advanced Configuration and Power Interface) specification. Enable Hibernation This item allows users to enable or disable system ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.
FabiaTech Corporation CPU Configuration You can use this screen to select options for the CPU Configuration Parameters. Hyper-Threading Enable for Windows XP and Linux(OS optimized for Hyper-Threading Technology) and Disable for other OS(OS not optimized for Hyper-Threading Technology). Available Options: Disabled, and Enabled...
Page 29
FabiaTech Corporation Limit CPUID Maxmum This item allows users to enable or disable limit CPUID maximum, To disable this item when Windows XP. Available Options: Disabled, and Enabled Default setting: Disabled...
FabiaTech Corporation Intel Fast Flash Standby You can use this screen to select options for the Intel Fast Flash Standby Technology Configuration. iFFS Support This item allows users to enable or disable iFFS(Intel Fast Flash Standby). Please refer to Chapter4 – iFFS setup procedure.
FabiaTech Corporation USB Configuration You can use this screen to select options for the USB Configuration. Legacy USB Support Legacy USB Support refers to the USB mouse and USB keyboard support. Normally if this option is not enabled; any attached USB mouse or USB keyboard will not become available until a USB compatible operating system is fully booted with all USB drivers loaded.
Page 32
FabiaTech Corporation USB transfer time-out The time-out value for control, bulk, and interrupt transfers. Available Options: 1 sec, 5 sec, 10 sec, and 20 sec Default setting: 20 sec Device reset time-out USB mass storage device start unit command time-out.
FabiaTech Corporation IDE Configuration You can use this screen to select options for the IDE devices Configuration. SATA Controller(s) This item allows users to enable or disable SATA Controller. Available Options: Disabled, and Enabled Default setting: Enabled Configure SATA as Select a configuration for SATA controller.
Page 34
FabiaTech Corporation SATA Port 0 The system SATA HDD corresponding SATA port 0, This item allows users to enable or disable SATA port 0. Available Options: Disabled, and Enabled Default setting: Enabled SATA Port 1 The CFast socket corresponding to the SATA port 1, This item allows users to enable or disable SATA port 1.
FabiaTech Corporation Super IO Configuration This section describes the function of Super I/O settings.
Page 36
FabiaTech Corporation Serial Port 1 Configuration Set Parameters of Serial Port 1. (COMA) Serial Port This item allows users to enable or disable Serial Port 1. Available Options: Disabled, and Enabled Default setting: Enabled...
Page 37
FabiaTech Corporation Serial Port 2 Configuration Set Parameters of Serial Port 2. (COMB) Serial Port This item allows users to enable or disable Serial Port 2. Available Options: Disabled, and Enabled Default setting: Enabled...
Page 38
FabiaTech Corporation Serial Port 3 Configuration Set Parameters of Serial Port 3. (COMC) Serial Port This item allows users to enable or disable Serial Port 3. Available Options: Disabled, and Enabled Default setting: Enabled...
Page 39
FabiaTech Corporation Serial Port 4 Configuration Set Parameters of Serial Port 4. (COMD) Serial Port This item allows users to enable or disable Serial Port 4. Available Options: Disabled, and Enabled Default setting: Enabled...
Page 43
FabiaTech Corporation Memory Frequency and Timing Config memory frequency and timing settings. MRC Fast Boot This item allows users to enable or disable MRC fast boot. Available Options: Disabled, and Enabled Default setting: Enabled Max TOLUD Maximum Value of TOLUD Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller.
Page 44
FabiaTech Corporation Intel IGD Configuration Config Intel IGD Settings IGFX – Boot Type Select the Video Device which will be activated during POST. Available Options: CRT, HDMI, Display Port Default setting: CRT...
FabiaTech Corporation South Bridge South Bridge Parameters.
Page 46
FabiaTech Corporation TPT Devices Enable/Disable Intel® IO Controller Hub(TPT) Devices. Azalia Controller This item allows users to enable or disable Azalia Controller. Available Options: Disabled, and HD Audio Default setting: HD Audio USB 2.0(EHCI) Support This item allows users to enable or disable USB 2.0 (EHCI) Support.
Page 47
FabiaTech Corporation SMBus Conotroller This item allows users to enable or disable on-chip SMBus controller. Available Options: Disabled, and Enabled Default setting: Enabled...
Page 48
FabiaTech Corporation PCI Express Root Port 1 (On Board LAN1) PCI Express Root Port 1 Settings. PCI Express Port 1 The system on board LAN 1 corresponding port 1, This item allows users to enable or disable PCI Express Root Port1.
Page 49
FabiaTech Corporation PCI Express Root Port 2 (On Board LAN2) PCI Express Root Port 2 Settings. PCI Express Port 2 The system on board LAN 2 corresponding port 2, This item allows users to enable or disable PCI Express Root Port2.
Page 50
FabiaTech Corporation PCI Express Root Port 3 PCI Express Root Port 3 Settings. PCI Express Port 3 The halt size Mini Card socket corresponding port 3, This item allows users to enable or disable PCI Express Root Port3. Available Options: Disabled, Enabled, and Auto...
Page 51
FabiaTech Corporation High Precision Timer This item allows users to enable or disable the High Precision event timer. Available Options: Disabled, and Enabled Default setting: Enabled Restore AC Power Loss This field specifies the option controls how the PC will behave once power is restored following a power outage (or other unexpected or ungraceful shutdown).
FabiaTech Corporation Boot Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Device Priority, to go to the sub menu for that item. You can display a Boot BIOS Setup option by highlighting it using the <Arrow>...
Page 53
FabiaTech Corporation Quiet Boot This item allows users to enable or disable Quiet boot option. If enable, an OEM LOGO will replace the POST messages. Available Options: Disabled, and Enabled Default setting: Disabled Boot Option Priorities Allows users to set the device boot priorities in this sub-title the following.
Page 54
FabiaTech Corporation CSM parameters OpROM Execution, boot options filter, ect. Launch PXE OpROM policy Controls the execution of UEFI and Legacy PXE OpROM. Available Options: Do not launch, UEFI only, and Legacy only Default setting: Do not launch...
FabiaTech Corporation Security There are two security passwords: Administrator and User. Administrator a privileged person that can change the User password from the BIOS. According to the default setting, both access passwords are not set up and are only valid after you set the password from the BIOS.
FabiaTech Corporation Save & Exit Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving the changes. Discard Changes and Reset...
Page 57
FabiaTech Corporation Save Changes Save changes done so far to any of the setup options. Discard Changes Discard changes done so far to any of the setup options. Restore Defaults Restore/Load Default values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults.
FabiaTech Corporation Chapter 4 Software Installation The enclosed CD diskette includes FX5653 VGA, Audio, System, and LAN driver. To install and configure you FX5653 system, you need to perform the following steps. System Driver WIN 7 Driver Installs Atom D2000 Chipset, Core PCI, PCIe, SATA, USB, ISAPnP and IDE/ATA Device Drive.
FabiaTech Corporation VGA Driver 7 Driver Step 1: To install the VGA driver, insert the CD ROM into the CD ROM device, and enter DRIVER>VGA> ATOM_CedarTrail>WIN7. Step 2: Execute SETUP.EXE file. Step 3: The screen shows the SETUP type. Press any key to enter the main menu.
FabiaTech Corporation LAN Driver (RTL 8111C) WIN7 Driver The Win7 has include RTL8111C driver, please follow the steps if you want to update driver. Step 1: To install the LAN driver, insert the CD ROM into the CD ROM device, and enter DRIVER>LAN>RTL8111F\WIN7.
FabiaTech Corporation iFFS setup procedure STEP1: Install WIN7 on SSD. While installing, partition a portion of SSD which will be used for iFFS. Size of this partition has to be a minimum of the DRAM size. It is recommended, if possible, to make this partition at least as big as the big as the largest DRAM that can be used on this platform.
Page 62
FabiaTech Corporation SETP3 : Reserving partition as hibernation partition: Launch Disk Partitioning tool – standard tool available in Windows 7. Go to . Type cmd.exe in the search bar. Type diskpart.exe and press enter. Click on yes when it prompts for User Account Control DiskPart. A new window for diskpart will show up as shown below.
Page 63
FabiaTech Corporation The hibernation partition will be identified as shown below. SETP4 : Boot up the system and go into BIOS setup. Go to Advanced tab and select Intel Fast Flash Standby. iFFS Support Enabled Save and Exit...
FabiaTech Corporation Watchdog Timer This section describes how to use the Watchdog Timer, including disabled, enabled, and trigger functions. The system is equipped with a programmable time-out period watchdog timer. You can use your own program to enable the watchdog timer. Once you have enabled the watchdog timer, the program should trigger the I/O every time before the timer times out.
FabiaTech Corporation Watchdog Timer Setting The watchdog timer is a circuit that may be used from your program software to detect system crashes or hang-ups. The watchdog timer is automatically disabled after reset. Once you have enabled the watchdog timer, your program must trigger the watchdog timer every time before it times out.
FabiaTech Corporation Watchdog Timer Enabled To enable the watchdog timer, you have to output a byte of timer factor to the watchdog register whose address is 2eh and data port is 2fH. The following is an Assemble program, which demonstrates how to enable the watchdog timer and set the time-out period at 28 seconds.
FabiaTech Corporation al,28h ; Set timeout interval as 28seconds and start counting dx,al ;------------------------------------------ ; Exit extended function mode ;------------------------------------------ dx,2eh al,01h dx,al Watchdog Timer Trigger After you enable the watchdog timer, your program must write the same factor as enabling to the watchdog register at least once every time-out period to its previous setting.
FabiaTech Corporation TTL I/O(GPIO) programming The following is an Assembly program, which demonstrates how to set the GPIO type and how to read and write values. ;------------------------------------------------------------------------------------------ ; Enter the extended function mode, interruptible double-write ;------------------------------------------------------------------------------------------ dx, 2eh ; Enter to extended function mode...
FabiaTech Corporation Chapter 5 Technical Reference This section outlines the errors that may occur when you operate the system, and also gives you the suggestions on solving the problems. Topic include: Trouble Shooting for Post Beep & Error Messages Technical Reference Trouble Shooting for Post Beep and Error Messages The following information informs the Post Beep &...
Page 71
FabiaTech Corporation CMOS Checksum Bad This error informs that the CMOS has corrupted. When the battery runs weak, this situation might happen. Please check the battery and change a new one when necessary. DISK BOOT FAILURE When you can‘t find the boot device, insert a system disk into Drive A and press <...
Page 72
FabiaTech Corporation MEMORY ADDRESS ERROR When the memory address indicates error, you can use this location along with the memory map for your system to find and replace the bad memory chips. MEMORY SIZE HAS CHANGED Memory has been added or removed since last boot. In EISA mode, use Configuration Utility to re-configure the memory configuration.
5°C to 45°C (W/HDD)/0°C to 50°C (W/CF card only) Real-Time Clock and Non-Volatile RAM The FX5653 contains a real-time clock compartment that maintains the date and time in addition to storing configuration information about the computer system. It contains 14 bytes of clock and control registers and 114 bytes of general purpose RAM.
Page 74
FabiaTech Corporation Address Description Status register B Status register C Status register D Diagnostic status byte Shutdown status byte Diskette drive type byte, drive A and B Fixed disk type byte, drive C Fixed disk type byte, drive D Reserved...
FabiaTech Corporation CMOS RAM Map Register Description 00h -10h Standard AT-compatible RTC and Status and Status Register data definitions 11h – 13h Varies Equipment Bits Number of Floppy Drives 1 Drive 2 Drives Bits Monitor Type Not CGA or MDA 01 40x25 CGA...
FabiaTech Corporation I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses, which also becomes the identity of the device. There is a total of 1K-port address space available. The following table lists the I/O port addresses used on the Industrial CPU Card.
FabiaTech Corporation Interrupt Request Lines (IRQ) There are a total of 15 IRQ lines available on the Industrial CPU Card. Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on the Industrial CPU Card.
FabiaTech Corporation Serial Ports The ACEs (Asynchronous Communication Elements ACE1 to ACE2) are used to convert parallel data to a serial format on the transmit side and convert serial data to parallel on the receiver side. The serial format, in order of transmission and reception, is a start bit, followed by five to eight data bits, a parity bit (if programmed) and one, one and half (five-bit format only) or two stop bits.
Page 79
FabiaTech Corporation Bit 1: Enable Transmitter Holding Empty Interrupt (ETBEI) Bit 2: Enable Receiver Line Status Interrupt (ELSI) Bit 3: Enable MODEM Status Interrupt (EDSSI) Bit 4: Must be 0 Bit 5: Must be 0 Bit 6: Must be 0...
Page 80
FabiaTech Corporation Bit 5: Stick Parity Bit 6: Set Break Bit 7: Divisor Latch Access Bit (DLAB) MODEM Control Register (MCR) Bit 0: Data Terminal Ready (DTR) Bit 1: Request to Send (RTS) Bit 2: Out 1 (OUT 1) Bit 3: Out 2 (OUT 2)
Page 81
FabiaTech Corporation Bit 4: Clear to Send (CTS) Bit 5: Data Set Ready (DSR) Bit 6: Ring Indicator (RI) Bit 7: Received Line Signal Detect (RSLD) Divisor Latch (LS, MS) Bit 0: Bit 0 Bit 8 Bit 1: Bit 1...