Related Manuals for FabiaTech FX5634 Fanless Series
Summary of Contents for FabiaTech FX5634 Fanless Series
- Page 1 FabiaTech Corporation IPC Solution Website: http://www.fabiatech.com Email: support@fabiatech.com Small Cube System Fanless Series FX5634 User’s Manual JAN 2009 Version: 1.0 Part Number: FX5634...
- Page 2 FabiaTech shall not be reliable for technical or editorial errors or omissions, which may occur in this document. FabiaTech shall not be reliable for any indirect, special, incidental or consequential damages resulting from the furnishing, performance, or use of this document.
-
Page 3: Table Of Contents
Table of Contents FX5634 User’s Manual ......................i Chapter 1 Introducing the FX5634 System ................1 Overview..........................1 Series Comparison Table .......................2 Layout............................3 Specifications..........................4 Packing List ..........................5 Chapter 2 Hardware Installation ....................7 Before Installation ........................7 Removing Covers –Installing Hardware............8 LED Indicators (On the Front Panel)...............17 ... - Page 4 Boot Setup ..........................39 Boot Setting Configuration ................40 Boot Device .......................42 Hard Disk Drives ....................43 Security setup........................44 Chipset Setup........................46 Northbridge Configuration................46 Southbridge Configuration................47 AMD 690E Configuration .................48 Onboard Peripherals Configuration ..............49 POWER MANAGEMENT......................51 Power Management/APM ................51 ...
- Page 5 Physical and Environmental ..................68 Supports CPU Type List ....................68 Real-Time Clock and Non-Volatile RAM ..............68 CMOS RAM Map......................70 I/O Port Address Map....................71 Interrupt Request Lines (IRQ) ..................72 DMA Channel Map ....................73 DMA Controller 2......................73 Serial Ports ........................74 Appendix........................... 78 Dimension ..........................78...
-
Page 7: Chapter 1 Introducing The Fx5634 System
FabiaTech Corporation Chapter 1 Introducing the FX5634 System Overview The FX5634 is an embedded system with low-power CPU module inside. This user’s manual provides information on the physical features, installation, and BIOS setup of the FX5634. Built to unleash the total potential of the AMD - Sempron uPGA 638 pin S1 Processors with 800 MHz Front Side Bus ( FSB), Able to supports 1600Mhz ~ 2000Mhz CPU, this system supports two 10/100/1000M Base –TX LAN ports, DDR2 667MHz-RAM,... -
Page 8: Series Comparison Table
FabiaTech Corporation Series Comparison Table Model FX5634 System Processor AMD Mobile Sempron N+S Chipset AMD RS690E +SB600 2 200 Pin-DIMM (Max.) DDR2 533/667MHz 1GB/2GB/4GB Watchdog Timer Multi I/O Two RS232 Storage One CF /One ATA/Two SATA2 COMBO Drive DVD/CD-RW(OPTION) USB 2.0... -
Page 9: Layout
FabiaTech Corporation Layout RESET POWER POWER SWITCH LIGHT LIGHT MOUSE LAN2 LAN1 COM4 COM3 COM2 COM1 OUT IN MIC ANTENNA AC/110~240V KEYBOARD DC IN 8V~20V... -
Page 10: Specifications
FabiaTech Corporation Specifications Processor Board – AMD Mobile Sempron 638-pin Processor 2 SoDIMM slot support DDR II 533 /667 MHz SDRAM Up to 4GB I/O Outlets – One 10/100 and One 10/100/1000 base-TX Ethernet LAN ports. Four USB ports (2.0) and two RS-232 serial ports. -
Page 11: Packing List
FabiaTech Corporation Packing List Upon receiving the package, verify the following things. Should any of the mentioned happens, contact us for immediate service. • Unpack and inspect the FX5634 package for possible damage that may occur during the delivery process. - Page 12 FabiaTech Corporation...
-
Page 13: Chapter 2 Hardware Installation
FabiaTech Corporation Chapter 2 Hardware Installation This chapter introduces the system connectors & jumper settings, and guides you to apply them for field application. Before Installation Before you install the system, make sure you follow the following descriptions. 1. Before removing the cover, shut down the operation System and disconnect power switch to off and unplug AC power code cable. -
Page 14: Removing Covers -Installing Hardware
FabiaTech Corporation Removing Covers –Installing Hardware If you are installing hardware option, you can remove the top or bottom cover. The following figure will guide you how to install 2.5" HDD inside, Compact Flash modules, expansion PCI card, mini PCI WLAN module and DDR2-RAM module the FX5634 and how to install the FX5634 fixers. - Page 15 FabiaTech Corporation b. Installing Mini PCI Card: Mini PCI Socket for WLAN Modules You may extend additional mini PCI WLAN module to FX5634 by removing the top cover. Connect the antenna cable from left side antenna hole to Mini PCI WLAN (the auxiliary board).
- Page 16 FabiaTech Corporation b2-1. Antenna Cable b2-2. Connect to the WLAN module b3. Screw the Antenna...
- Page 17 FabiaTech Corporation c. Installing Memory & Compact Flash: DIMM1/2 and CF Socket The FX5634 support 2 DIMM socket and Compact flash socket, See as following figure and rear pictures. The DIMM socket supports 512MB to 2GB of DDR2 RAM modules.
- Page 18 FabiaTech Corporation c2. Unscrew and remove the bottom side cover c3. DIMM2 and CF Socket: Installing Memory and Compact Flash Module...
- Page 19 FabiaTech Corporation d. Installing PATA or SATA Hard Disk The following figure will guide you install fix support HDD and to inside the FX5634. d1. Screw the HDD Metal Frame to the HDD Note: Use caution when handling the hard disk to prevent damage to IDE1 connector (-pin) as you inserted PATA hard disk.
- Page 20 FabiaTech Corporation d2. Screw the HDD Metal Frame e. Installing Expansion PCI Card If you are installing Expansion PCI hardware, you can remove the top side cover. The following figure will guide you how to install PCI interface card inside the...
- Page 21 FabiaTech Corporation e1. Add the L-Type Metal: Screw the L-Type Metal on the PCI card Bracket e2. Installing PCI card e3. Screw the PCI card...
- Page 22 FabiaTech Corporation e3. PCI card Limit Dimension f. Installing the L-Type Universal fixers Please refer to the back side figure for installing the FX5634 with universal fixers.
-
Page 23: Led Indicators (On The Front Panel)
FabiaTech Corporation g. Screw Plastic Foot Please refer to the back side figure for installing the FX5634 with plastic foot. LED Indicators (On the Front Panel) The Power and HDD LED’s has two distinctive statuses: Off for inactive operation and blinking light for activity. -
Page 24: Connecting The Monitor, Keyboard And Mouse
FabiaTech Corporation Connecting the Monitor, Keyboard and Mouse If you are connecting the monitor, keyboard, mouse to the FX5634 using the connections provided on the side of the chassis. See following figure and a side pictures. MOUSE LAN2 LAN1 COM4... -
Page 25: Connecting The Com Ports
FabiaTech Corporation Connecting the COM ports The DB9 (COM1/2/3/4) is standard serials port connector. The following tables show the signal connections of these connectors. DB-9 RS-232 Signal -DCD -DSR -RTS -TXD -CTS -DTR Note Ground Case Case Ground Note: The COM1&COM2 pin-9 RI# signal by JU6/JU7 jumper selection. -
Page 26: Connecting The Audio Microphone-In/ Line-In/ Speak Out
FabiaTech Corporation Connecting the Audio Microphone-In/ Line-In/ Speak Out Mic-In SPK-Out Line-In Connecting the AC Power core Power is supplied through AC power cable. Plug its power into a power outlet then push power button, when you final installed system hardware device. -
Page 27: Jumper Setting
FabiaTech Corporation Jumper Setting The COM2 is designed for multiple proposes, Use JP2/JP3/JU7 of the CPU board selects RS-232, RS422 or RS-485 of COM2 connector(Please see the spots circled), and JU5,J3 of CPU board is used to select clear CMOS data, and select master or slave device of this Compact Flash socket. - Page 28 FabiaTech Corporation b. J3: Compact Flash Master/Slave Selection The Compact Flash socket (on the bottom side) is optional and supports 3.3V Compact Flash and Micro Drives. J3 is used to select master/slave device of this socket. Be sure to ward off the same master/slave setting with which connects to IDE1 connector, if you use IDE1 and compact flash simultaneously.
-
Page 29: Chapter 3 Bios Setup
FabiaTech Corporation Chapter 3 BIOS Setup This chapter describes the BIOS setup. Overview BIOS are a program located on a Flash memory chip on a circuit board. It is used to initialize and set up the I/O peripherals and interface cards of the system, which includes time, date, hard disk drive, the ISA bus and connected devices such as the video display, diskette drive, and the keyboard. -
Page 30: Bios Functions
FabiaTech Corporation BIOS Functions On the menu, you can perform the following functions 1. Main 2. Advanced CPU Configuration IDE Configuration SuperIO Configuration Hardware Health Configuration ACPI Function Event Log Configuration USB Configuration 3. PCIPnP 4. Boot Boot Settings Configuration... -
Page 31: Keyboard Convention
FabiaTech Corporation North Bridge Configuration South Bridge Configuration AMD 690E Configuration Onboard Peripherals Configuration 7. Power 8. Exit Save Changes and Exit: Exit system setup after saving the changes.F10 key can be used for this operation. Discard Changes and Exit: Exit system setup without saving any changes. -
Page 32: Main Setup
FabiaTech Corporation Main Setup This section describes basic system hardware configuration, system clock setup and BIOS version information. If the CPU board is already installed in a working system, you will not need to select this option anymore. System Memory This option is display-only which is determined by POST (Power On Self Test) of the BIOS. -
Page 33: Advanced Setup
FabiaTech Corporation Advanced Setup Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as SuperIO Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>... -
Page 34: Ide Configuration
FabiaTech Corporation IDE Configuration You can use this screen to select options for the IDE Configuration Settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. - Page 35 FabiaTech Corporation Hard Disk Type The BIOS supports various types for user settings, The BIOS supports <Pri Master>, <Pri Slave>, so the user can install up to two hard disks. For the master and slave jumpers, please refer to the hard disk’s installation descriptions and the hard disk jumper settings.
-
Page 36: Superio Chipset - Configuration Ite8712 Super Io Chipset
FabiaTech Corporation ATA (PI) 80 Pin Cable Detection Set this option to select the method used to detect the ATA (PI) 80 pin cable. The use of an 80-conductor ATA cable is mandatory for running Ultra ATA/66, Ultra ATA/100 and Ultra ATA/133 IDE hard disk drives. The standard 40-conductor ATA cable cannot handle the higher speeds. - Page 37 FabiaTech Corporation Available Options: Disabled, 2F8H/IRQ3, 3E8H/IRQ4, and 2E8H/IRQ3. Default setting: 2F8H/IRQ3 Serial Port 3 Address These fields select the I/O port address for each Serial port. Available Options: Disabled, 3E8, 2E8, 2F0, 2E0, 2D8, and 2D0. Default setting: 3E8H/IRQ3 Serial Port3 IRQ These fields select the Serial Port 3 Interrupt.
-
Page 38: Hardware Health Configuration
FabiaTech Corporation Hardware Health Configuration On the Hardware Monitor Setup screen, you can monitor the system temperature, CPU voltage, and CPU fan speed…... -
Page 39: Advanced Acpi Settings
FabiaTech Corporation Advanced ACPI Settings General ACPI Configuration Suspend Mode This filed specifies allow you select the ACPI states used for system suspend. Available Options: S1 (POS), S3 (STR), and AUTO Default setting: S1 (POS) Advanced ACPI Configuration ACPI Version Features Set this value to allow or prevent the system to be complaint with the ACPI specification. -
Page 40: Usb Configuration
FabiaTech Corporation ACPI APIC Support Allows you to enable or disable the ACPI APIC table pointer to RSDT point list. Available Options: Disabled, and Enabled Default setting: Enabled AMI OEMB Table Set this value to allow the ACPI BIOS to add a pointer to an OEMB table in the Root System Description Table (RSDT) table. - Page 41 FabiaTech Corporation Available Options: Disabled, Enabled and AUTO Default setting: Enabled USB 2.0 Controller Mode This field is configures the USB 2.0 controllers in High speed (480Mbps) or Full speed (12Mbps). Available Options: HiSpeed and FullSpeed Default setting: Hispeed BIOS ECHI Hand-Off This is a workaround for OS without ECHI Hand-Off support.
-
Page 42: Pcipnp Setup
FabiaTech Corporation PCIPnP Setup Select the PCI/PnP tab from the setup screen to enter the Plug and Play BIOS Setup screen. You can display a Plug and Play BIOS Setup option by highlighting it using the <Arrow> keys. All Plug and Play BIOS Setup options are described in this section. The Plug and Play BIOS Setup screen is shown below. - Page 43 FabiaTech Corporation PCI Latency Timer This field specifies the latency timings (in PCI clock) PCI devices installed in the PCI expansion bus. Available Options: 32, 64, 96, 128, 160,192, 224, and 248 Default setting: 64 Allocate IRQ to PCI VGA When a PCI or AGP VGA device is installed, you can assign an IRQ to this device.
- Page 44 FabiaTech Corporation IRQ 3 –15 When I/O resources are controlled manually, you can assign each system interrupt as one of the following types, based on the type of device using the interrupt: Available: Specified IRQ is available to the used by PCI/PnP devices.
-
Page 45: Boot Setup
FabiaTech Corporation Boot Setup Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Device Priority, to go to the sub menu for that item. You can display a Boot BIOS Setup option by highlighting it using the <Arrow>... -
Page 46: Boot Setting Configuration
FabiaTech Corporation Boot Setting Configuration Quick Boot This field is used to activate the quick boot function of the system. When set to Enabled, 1. BIOS will not wait for up to 40 seconds if a Ready signal is not received from the IDE drive, and will not configure its drive. - Page 47 FabiaTech Corporation Available options: On, Off Default setting: On PS/2 Mouse Support The PS/2 mouse function is optional. Before you configure this field, make sure your FX5632 supports this feature. The setting of Enabled allows the system to detect a PS/2 mouse on boot up.
-
Page 48: Boot Device
FabiaTech Corporation Boot Device Use this screen to specify the order in which the system checks for the device to boot from. To access this screen, select Boot Device Priority on the Boot Setup screen and press <Enter>. First /Second /Third Hard Disk Boot Device Set the boot device options to determine the sequence in which the computer checks which device to boot from. -
Page 49: Hard Disk Drives
FabiaTech Corporation Hard Disk Drives Use this screen to view the hard disk drives in the system. To access this screen, select Hard disk drives on the Boot Setup screen and press <Enter>. -
Page 50: Security Setup
FabiaTech Corporation Security setup There are two security passwords: Supervisor and User. Supervisor is a privileged person that can change the User password from the BIOS. According to the default setting, both access passwords are not set up and are only valid after you set the password from the BIOS. - Page 51 FabiaTech Corporation 5. Select System or Setup. Always: a visitor who attempts to enter BIOS or operating system will be prompted for password. Setup: a visitor who attempts to the operating system will be prompted for user password. You can enter either User password or Supervisor password.
-
Page 52: Chipset Setup
FabiaTech Corporation Chipset Setup This section describes the configuration of the board’s chipset features. • North Bridge Configuration • South Bridge Configuration • AMD690E Configuration • Onboard Peripherals Configuration Northbridge Configuration You can use this screen to select options for the North Bridge Configuration. Use the up and down <Arrow>... -
Page 53: Southbridge Configuration
FabiaTech Corporation Bank Interleaving This field is enabled bank memory interleaving. If Auto, the memory will be checked which executes 64 or 128 bits mode. Available Options: Auto, Disabled Default setting: Auto Enable Clock to ALL DIMMs This field is enabled unused clocks to DIMMs even memory slots are not populated. -
Page 54: Amd 690E Configuration
FabiaTech Corporation Available Options: Disabled and Auto Default setting: Auto USB 1.1 OHCI Controllers This is a workaround for OS without OHCI support. The ECHI ownership change should claim by OHCI driver. Available Options: Enabled and Disabled Default setting: Enabled USB 2.0 EHCI Controllers... -
Page 55: Onboard Peripherals Configuration
FabiaTech Corporation Available Options: Disable, SIDEPORT, UMA, and UMA+SIDEPORT Default setting: UMA UMA Frame Buffer Size This field is select UMA memory size. Available Options: Auto , 32MB, 64MB, 128MB, 256MB, 512MB and 1024MB Default setting: Auto Multifunction This field is select enabled or disabled the internal graphics control multifunction feature. - Page 56 FabiaTech Corporation OnBoard Realtek 8111B NIC This field specifies the Enable or Disable of the onboard LAN chip. Available Options: Disabled, Enabled Default setting: Enabled Realtek 8111B NIC OPTIROM This field specifies the PXE boot ROM of the onboard LAN chip.
-
Page 57: Power Management
FabiaTech Corporation POWER MANAGEMENT Power Management/APM Select Enabled to activate the chipset Power Management and APM (Advanced Power Management) features. Available Options: Disabled and Enabled Default setting: Enabled Suspend Time Out This field specifies the length of a period of system inactivity (like hard disk or video) while in Standby state. - Page 58 FabiaTech Corporation Power Button Mode This option specifies go into On/Off or Suspend when power button is pressed. Available Options: On/Off, and Suspend. Default setting: On/Off Video Power Down Mode This field specifies the power conserving state that video subsystem enters after the specified period of display inactivity has expired.
- Page 59 FabiaTech Corporation The "Last State" option returns the PC to the state in effect at the time the power outage or shutdown occurred. Assign this option the "Power On" value to reboot automatically; assign the "Power Off" value to leave the machine powered down.
- Page 60 FabiaTech Corporation...
-
Page 61: Chapter 4 Software Installation
FabiaTech Corporation Chapter 4 Software Installation The enclosed diskette includes FX5634 VGA, Audio, System and LAN driver. To install and configure you FX5634 system, you need to perform the following steps. Dotnetfix2.0 Driver For WIN XP Driver Install donetfix2.0 driver for Windows XP VGA driver. -
Page 62: Vga Driver
FabiaTech Corporation VGA Driver WIN XP/Vista32-64 Driver Step 1: To install the VGA driver, insert the CD ROM into the CD ROM device, and enter DRIVER>VGA>RS690M-E>WINXP, and Vista32_64. Step 2: Execute SETUP.EXE file. Step 3: The screen shows the SETUP type. Press any key to enter the main menu. -
Page 63: Lan Driver (Rtl-8111B)
FabiaTech Corporation LAN Driver (RTL-8111B) To install the LAN driver, insert the CD ROM into the CD ROM device, and enter DRIVER>LAN>RTL8111B>WINXP or Visat32_64. Execute Setup.exe. Note: In the LAN>RTL8111B>Vista32_64>README directory, a SETUP.HTML is included to provide installation information. BIOS Flash Utility In the <UTILITY>... -
Page 64: Watchdog Timer
FabiaTech Corporation Watchdog Timer This section describes how to use the Watchdog Timer, including disabled, enabled, and trigger functions. The FX5634 is equipped with a programmable time-out period watchdog timer. You can use your own program to enable the watchdog timer. Once you have enabled the watchdog timer, the program should trigger the I/O every time before the timer times out. -
Page 65: Watchdog Timer Setting
FabiaTech Corporation Watchdog Timer Setting The watchdog timer is a circuit that may be used from your program software to detect system crashes or hang-ups. The watchdog timer is automatically disabled after reset. Once you have enabled the watchdog timer, your program must trigger the watchdog timer every time before it times out. -
Page 66: Watchdog Timer Enable & Trigger
FabiaTech Corporation Watchdog Timer Enable & Trigger After you enable the watchdog timer, your program must write the same factor as enabling to the watchdog register at least once every time-out period to its previous setting. You can change the time-out period by writing another timer factor to the watchdog register at any time, and you must trigger the watchdog before the new time-out period in the next trigger. -
Page 67: Programming Rs-485
FabiaTech Corporation Programming RS-485 The majority communicative operation of the RS-485 is in the same of the RS-232. When the RS-485 precedes the transmission, which needs control the TXC signal, and the installing, steps are as follows: Step 1: Enable RTS... -
Page 68: Send Out One Character (Transmit)
FabiaTech Corporation Send out one character (Transmit) Step 1: Enable TXC signal, and the bit 1 of the address of offset+4 just sets “1”. Step 2: Send out the data. (Write this character to the offset+0 of the current COM port address) Step 3: Wait for the buffer’s data empty. - Page 69 FabiaTech Corporation RETURN b. Send out one character to COM2 REM Enable transmitter by setting RTS ON OUT &H2FC, (INP(&H2FC) OR &H02) REM Send out one character PRINT #1, OUTCHR$ REM Check transmitter holding register and shift register IF ((INP(&H2FD) AND &H60) >0) THEN 60 REM Disable transmitter by resetting RTS OUT &H2FC, (INP(&H2FC) AND &HFD)
- Page 70 FabiaTech Corporation...
-
Page 71: Chapter 5 Technical Reference
FabiaTech Corporation Chapter 5 Technical Reference This section outlines the errors that may occur when you operate the system, and also gives you the suggestions on solving the problems. Topic include: Trouble Shooting for Post Beep & Error Messages Technical Reference Trouble Shooting for Post Beep and Error Messages The following information informs the Post Beep &... - Page 72 FabiaTech Corporation CMOS CHECKSUM ERROR This error informs that the CMOS has corrupted. When the battery runs weak, this situation might happen. Please check the battery and change a new one when necessary. DISK BOOT FAILURE When you can‘t find the boot device, insert a system disk into Drive A and press <...
- Page 73 FabiaTech Corporation MEMORY ADDRESS ERROR When the memory address indicates error, you can use this location along with the memory map for your system to find and replace the bad memory chips. MEMORY SIZE HAS CHANGED Memory has been added or removed since last boot. In EISA mode, use Configuration Utility to re-configure the memory configuration.
-
Page 74: Technical Reference
FabiaTech Corporation Technical Reference Physical and Environmental Temperature: Operating 0°C ~ 40°C Relative humidity 5 % to 95 % non-condensing DC-AC adapter Input AC Voltage Range: 100V~240V/1A, 50Hz ~60Hz Output DC Voltage: 19V/3.42A Maximal Surface Temperature of Chassis： 5°C to 40°C (W/HDD)/0°C to 40°C (W/CF card only) - Page 75 FabiaTech Corporation Address Description Hour alarm Day of week Date of month Month Year Status register A Status register B Status register C Status register D Diagnostic status byte Shutdown status byte Diskette drive type byte, drive A and B...
-
Page 76: Cmos Ram Map
FabiaTech Corporation CMOS RAM Map Register Description 00h -10h Standard AT-compatible RTC and Status and Status Register data definitions 11h – 13h Varies Equipment Bits Number of Floppy Drives 1 Drive 2 Drives Bits Monitor Type Not CGA or MDA 01 40x25 CGA... -
Page 77: I/O Port Address Map
FabiaTech Corporation I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses, which also becomes the identity of the device. There is a total of 1K-port address space available. The following table lists the I/O port addresses used on the Industrial CPU Card. -
Page 78: Interrupt Request Lines (Irq)
FabiaTech Corporation Interrupt Request Lines (IRQ) There are a total of 15 IRQ lines available on the Industrial CPU Card. Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on the Industrial CPU Card. -
Page 79: Dma Channel Map
FabiaTech Corporation DMA Channel Map The equivalents of two 8237A DMA controllers are implemented in the FX5634 board. Each controller is a four-channel DMA device that will generate the memory addresses and control signals necessary to transfer information directly between a peripheral device and memory. This allows high speeding information transfer with less CPU intervention. -
Page 80: Serial Ports
FabiaTech Corporation Serial Ports The ACEs (Asynchronous Communication Elements ACE1 to ACE2) are used to convert parallel data to a serial format on the transmit side and convert serial data to parallel on the receiver side. The serial format, in order of transmission and reception, is a start bit, followed by five to eight data bits, a parity bit (if programmed) and one, one and half (five-bit format only) or two stop bits. - Page 81 FabiaTech Corporation Bit 1: Enable Transmitter Holding Empty Interrupt (ETBEI) Bit 2: Enable Receiver Line Status Interrupt (ELSI) Bit 3: Enable MODEM Status Interrupt (EDSSI) Bit 4: Must be 0 Bit 5: Must be 0 Bit 6: Must be 0...
- Page 82 FabiaTech Corporation Bit 5: Stick Parity Bit 6: Set Break Bit 7: Divisor Latch Access Bit (DLAB) MODEM Control Register (MCR) Bit 0: Data Terminal Ready (DTR) Bit 1: Request to Send (RTS) Bit 2: Out 1 (OUT 1) Bit 3: Out 2 (OUT 2)
- Page 83 FabiaTech Corporation Bit 4: Clear to Send (CTS) Bit 5: Data Set Ready (DSR) Bit 6: Ring Indicator (RI) Bit 7: Received Line Signal Detect (RSLD) Divisor Latch (LS, MS) Bit 0: Bit 0 Bit 8 Bit 1: Bit 1...
-
Page 84: Appendix
FabiaTech Corporation Appendix Dimension a. FX5634... - Page 85 FabiaTech Corporation b. FX5634 L-type universal fixers...
- Page 86 FabiaTech Corporation c. FX5634 Plastic foot...