Alarm Lock Trilogy DL4100 Programming Instructions Manual page 32

r
DL4100 Residency and Privacy Features
Privacy Feature Mode 1: (Door Normally Locked--Factory Default)
"Privacy Feature Mode 1" is designed to allow access to individuals with access codes and is typically used for rooms needing pri­
vacy from others such as bathrooms, dorms and meeting rooms (Factory Default).
Configuring the DL4100 for the "Privacy Feature Mode 1" will initially provide a normally locked state. To enter through a DL4100
monitored door the user must use an access code or key. Once inside, the user presses the button and automatically disables the
keypad from allowing another user to enter for a pre-programmed am ount of time. The red LED on the exterior / outside o f the lock
will blink indicating that the room is occupied. W hen the initial user exits, the DL4100 is automatically set back into the original locked
mode and allows access to any authorized users.
The disable time (lockout) for the DL4100 can be pre-programmed by the installer. The disable tim e can be programmed to disable
access code access for up to 250 minutes. All users 12 and higher are disabled when this feature is active. Users
can always override this lockout feature with their user codes.
Programming: Disable Keypad On Button Press
Default "Time-Out Duration" is automatically set to 10 minutes. This time is the maximum time the "Privacy Feature" is enabled. To
set this duration, enter the following sequence with your desired time from 001 -250 minutes.
Programming:
************************************************************************
Residency Feature:
The "Residency Feature" is provided to prevent a person from unintentionally having the door lock behind them when stepping out­
side briefly. Typically used in retirement homes and college dormitories.
Configuring the DL4100 for the "Residency Feature" will initially provide a normally locked state. To enter through a DL4100 moni­
tored door the user must use an access code or key. The DL4100 will then re-lock when door is closed.
Turning the handle and exiting from the inside will unlock the DL4100 and set it to passage mode.
A ny of the following will restore the lock to the normally secure mode.
1. The user returns, enters, and presses the button from the inside.
2. Someone already inside the premises presses the button.
3. Pre-programmed scheduling.
4. Entering a valid access code or locking with a key.
Programming:
Programming: Leave Unlocked on Exit (Passage)
Cancel Passage on Button Press
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Privacy Feature Mode 2: (Door Normally Unlocked)
"Privacy Feature Mode 2" is designed to allow access to all and is typically used for rooms needing tem porary privacy from others
such as bathrooms, dorms and meeting rooms.
Configuring the DL4100 for the "Privacy Feature Mode 2" will initially provide a normally unlocked (passage mode) state. No access
code is necessary to enter. Once inside, the user presses the button and automatically disables the keypad from allowing another
user to enter for a pre-programmed am ount of time. The red LED on the exterior / outside o f the lock will blink indicating that the
room is occupied. W hen the initial user exits, the DL4100 is automatically set back into the original unlocked (passage) mode and
the DL4100 will allow new access to all.
The lockout time for the DL4100 can be pre-programmed by the installer. The lockout tim e can be programmed to disable access
code access for up to 250 minutes. All users 12 and higher are disabled when this feature is active. Users 1 - 11 or a key can al­
ways override this lockout feature with their codes.
Programmed Schedules will override the state o f the lock using Functions 45 and 46. If it is required that programmed schedules do
not override passage mode, Enable/Disable Passage Mode using Functions 48/49.
Programming:
Programming: Disable Keypad On Button Press
Enable Passage Mode
Default "Time-Out Duration" is automatically set to 10 minutes. This time is the maximum time the "Privacy Feature" is enabled. To
set this duration, enter the following sequence with your desired time from 001 -250 minutes.
Programming:
32
Time-Out Duration
Clear Privacy Default
Note:
Clear Privacy Default
Time-Out Duration
Programmable Through DL-Windows & Keypad
ll^ ^ l 11^6
ll^ ^ l ll^ ^ l
ll^ ^ l ll^ ^ l
ll^ ^ l 11^6
ll^ ^ l 11^6
Programmable Through Keypad Only; Not DL-Windows
Function 45 may only be programmed by using the keypad. In addition,
ll^ ^ l ll^ ^ l
ll^ ^ l 11^6
II^ Q l ll^ ^ l 11^1
ll^ ^ l ll^ ^ l
1 1 1
-
ll^ ^ l ll^ ^ l 11^1
[ ____ ] 11^1
(3
digits)
ll^ ^ l ll^ ^ l ll^ ^ l 11^1
ll^ ^ l 1 1 ^6 1 1 ^1
ll^ ^ l ll^ ^ l 11^1
ll^ ^ l ll^ ^ l ll^ ^ l 11^1
ll^ ^ l ll^ ^ l 11^1
[ ____ ] 11^1
(3 digits)
or a key