Yamaha Vmax VMX17C 2009 Service Manual page 101

1. Front brake light switch lead
2. Brake hose (front brake master cylinder to
hydraulic unit)
3. Clutch switch lead
4. Left handlebar switch lead
5. Clutch hose
6. Wire harness
7. Coupler cover
8. Front right turn signal/position light lead
9. Front left turn signal/position light lead
10. Throttle cables
11. Left and right handlebar switch leads
12. Left handlebar switch couplers
13. Intake air temperature sensor
14. Right handlebar switch lead
15. Right handlebar switch coupler
16. SELECT/RESET button unit lead
17. Wire harness mounting panel
18. SELECT/RESET button unit coupler
19. Meter assembly 2 lead
20. Upper radiator inlet pipe
21. Meter assembly 1 couplers
22. Accelerator position sensor coupler
23. SELECT/RESET button unit lead
24. Cylinder identification sensor coupler
25. Ignition coil sub-wire harness 2 coupler
26. Front wheel sensor coupler
27. Meter assembly 1 lead
A. Fasten the right handlebar switch lead and front
brake light switch lead with the holder. Face the
catch of the holder forward.
B. Fit the SELECT/RESET button unit lead in the
groove in the coupler holder.
C. Fasten the left handlebar switch lead and clutch
switch lead with the holder. Face the catch of the
holder forward.
D. Fasten the wire harness and grommet on the
clutch hose with the holder.
E. Fasten the front left turn signal/position light lead,
front right turn signal/position light lead, and
grommet on the brake hose (front brake master
cylinder to hydraulic unit) with the holder.
F. Route the left and right handlebar switch leads to
the rear of the coupler holder.
G. Insert the projection on the left handlebar switch
coupler into the hole in the coupler holder.
H. The catch of the holder may be facing to the left or
right.
I. Face the catch of the holder outward.
J. Face the catch of the holder inward.
K. Fasten the front right turn signal/position light lead,
front left turn signal/position light lead, right
handlebar switch lead, and front brake light switch
lead with the plastic band. The leads may be
fastened in any order.
L. Point the end of the plastic locking tie forward, and
then cut off the excess end of the tie to 2
–
(0.08 0.20 in).
M. Insert the projection on the right handlebar switch
coupler into the hole in the coupler holder.
N. Route the SELECT/RESET button unit lead
between the upper radiator inlet pipe and the wire
harness mounting panel.
O. Route the throttle cables between the wire harness
mounting panel and the meter assembly 2 lead.
P. Route the throttle cables between the wire harness
mounting panel and the SELECT/RESET button
unit lead.
Q. Route the accelerator position sensor lead
between the throttle cables and the wire harness
mounting panel.
R. Position the end of the plastic locking tie along the
front frame. Make sure that the plastic locking tie
does not protrude out of its protective tube.
S. Pass a plastic locking tie through the holes in the
wire harness mounting panel, and then fasten the
cylinder identification sensor lead, front wheel
sensor lead, ignition coil sub-wire harness 2,
starter motor lead, and meter assembly 2 lead with
the tie. Align the plastic locking tie with the
positioning tape on the starter motor lead. The
leads may be fastened in any order.
T. Pass a plastic locking tie through the holes in the
wire harness mounting panel, and then fasten the
cylinder identification sensor lead, front wheel
sensor lead, and ignition coil sub-wire harness 2
with the tie. Position the end of the plastic locking
tie along the wire harness mounting panel, and
then cut off the excess end of the tie to 1
(0.04
U. Insert the projection on the SELECT/RESET
button unit coupler into the hole in the wire harness
mounting panel.
V. Fasten the meter assembly 1 lead at the split in the
harness with a plastic locking tie. Point the end of
the plastic locking tie toward the front frame, and
then cut off the excess end of the tie to 1
(0.04
W. Insert the projection on the plastic band into the
hole in the wire harness mounting panel, and then
fasten the wire harness with the band.
–
5 mm
2-48
CABLE ROUTING
–
0.20 in).
–
0.20 in).
–
5 mm
–
5 mm