Kirisun PT3600 Instruction Manual
  1. Manuals
  2. Brands
  3. Kirisun Manuals
  4. Transceiver
  5. PT3600
  6. Instruction manual

Kirisun PT3600 Instruction Manual

Fm handheld transceiver
Hide thumbs Also See for PT3600:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, User Manual
PT3600
FM HANDHELD TRANSCEIVER
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT3600 and is the answer not in the manual?

Questions and answers

Related Manuals for Kirisun PT3600

Summary of Contents for Kirisun PT3600

  • Page 1 PT3600 FM HANDHELD TRANSCEIVER INSTRUCTION MANUAL...
  • Page 2 PT3600 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand two-way radios produced by Shenzhen Kirisun Electronics Co., Ltd. We believe two-way radio, which always incorporates the latest technology, can bring great convenience to your life and work;...
  • Page 3 (where the air off and remove the battery from the radio and contact contains gas, dust and smog, etc.), such as while your local authorized Kirisun dealer without delay. taking on fuel, or while parking at a gasoline service station.

  • Page 4: Table Of Contents

    1. Unpacking and Checking Content Unpack the radio carefully. We recommend that you 1. Unpacking and Checking........2 6. Scan Function............12 check the radio and the supplied accessories listed in 2. Preparation............3 7. Auxiliary Functions..........13 the following table before discarding the packing Power Antenna 2.1 Charging the Battery........3...

  • Page 5: Preparation

    Before the initial use, please charge the new battery. of the radio. Plug the power adapter into an applicable AC outlet • KB-31A Li-poly battery of Kirisun is applicable to this and connect the power adapter to the battery charger. radio.

  • Page 6: Installing The Antenna

    2.3 Installing the Antenna To remove the battery pack, push the battery latch 2.4 Installing the External Speaker/MIC 2.5 Installing/Removing the Belt Clip upwards, and then remove the battery away from the Hold the base of the antenna and turn the antenna Open the cover for external speaker/MIC jacks, and Align the grooves of the belt clip with those on the radio.

  • Page 7: Radio Overview

    3. Radio Overview 4. Basic Operations software. ④Emergency Button 4.2 Adjusting the Volume 4.1 Switching On Press the button to activate warning tone. Press it Turn the On-Off/Volume Control Knob to adjust the Turn the On-Off/Volume Control Knob clockwise until again to exit the emergency alert state.

  • Page 8: Selecting A Channel

    4.3 Selecting a Channel 4.4 Sending a Call 5. Functions of Programmable Monitor ● Press the preprogrammed Monitor button to open Turn the channel selector knob to your desired To make a call, press and hold the PTT button and Buttons squelch for monitoring the transmission on the channel.

  • Page 9: Scan Function

    6. Scan Function Before using VOX, you must set VOX gain level. available: again during the scanning to stop scanning. Such setting enables the radio to identify the voice (1) Last Rx channel: High/Low Power Switch ● (this function can be disabled by the dealer) When pressing the PTT button during scanning, the Press the preprogrammed High/Low Power Switch volume.

  • Page 10: Auxiliary Functions

    7. Auxiliary Functions is being conducted for 8 seconds, the radio will You can choose to set one of the following 3 alert tone will be sounded, and the transmission is ● enter Battery Saving Mode. When a signal is operations when the channel is switched during forbidden.

  • Page 11: Ctcss/Dcs

    monitoring state. used to notify the identity of the callers to the 8. Troubleshooting monitoring center, or used to activate the repeater. 7.6 CTCSS/DCS The encoder sequence and the encoder type can be CTCSS/DCS tones may have been pre-programmed Problem Causes and Solutions set for each channel.

  • Page 12: Major Specifications

    10. Status Setting 9. Major Specifications (by the dealer) Model: Serial No.: Problem Causes and Solutions 1. Channel setting PT3600 Model 136-174MHz VHF Channel No. Tx frequency Rx frequency CTCSS/DCS A.Make sure the antenna is well connected. Frequency 400-470MHz UHF The communication range is B.Make sure the antenna is the original supplied one.
  • Page 13 2. The way to resume scanning after its pause: □ Time Operate NOTE： NOTE： □ Carrier Operate 3. Revert channel: □ Selected Channel □ Selected Channel or Currently Working Channel □ Priority Channel □ Priority Channel or Currently Working Channel □...

Table of Contents