Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kirisun PT7200
Summary of Contents for Kirisun PT7200
-
Page 1: Instruction Manual
INSTRUCTION MANUAL PT7200 FM HANDHELD TRANSCEIVER... - Page 2 INSTRUCTION MANUAL PT7200 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand two- way radios produced by Kirisun Electronics (Shenzhen) Co., Ltd. We believe two-way radio, which always incorporates the latest technology, can bring great convenience to your life and work;...
- Page 3 areas or on unstable surfaces. Do not modify this radio for any reason. Refer service to qualified licensed or certificated technicians only. Notice to the User: Government laws prohibit radio communication without permission in government districts. Illegal operation is subject to punishment by fine and/or imprisonment.
-
Page 4: Table Of Contents
If the radio emits smoke or strange odors, turn it off and remove Installing/Removing the Belt Clip.............4 the battery from the radio and promptly contact your local authorized RADIO OVERVIEW...............5 Kirisun dealer. BASIC OPERATIONS..............6 PROGRAMMABLE BUTTON FUNCTION...........7 VOX (Voice Operated Transmission)............13 WIRED CLONING MODE.............13... -
Page 5: Supplied Accessories
* The battery is not fully charged in the factory, and please charge the new battery when you use the radio for the first time. * The radio is supplied with a KB-70A Ni-MH/KB-70B Lithium battery Charger Battery Hand Strap manufactured by KIRISUN. -
Page 6: Installing/Removing The Battery Pack
INSTALLING THE ANTENNA * When you charge the battery for the first time after purchasing or long storage (over 2 months), you should repeat charging it several times to achieve the normal battery capacity. Screw the antenna into the connector at * Do not recharge the battery if it has been fully charged or the battery the top of the radio by holding the power doesn't become low, otherwise it might affect the battery life or... -
Page 7: Radio Overview
RADIO OVERVIEW Side Button 1 (Programmable Button) Side Button 2 (Programmable Button) Top Button (Programmable Button) Speaker/Microphone Jacks Used to connect the optional speaker/microphone. BASIC OPERATIONS Switch On Switch on the radio by turning the Power/Volume switch clockwise till a click is heard, then the radio will be in the state of LED Indicator stand by and you will hear a beep if the dealer... -
Page 8: Programmable Button Function
High/Low Power Switch Make a Call Squelch Level adjust / Check To make a call, select the desired channel, Monitor Momentary/Call Cancel press and hold the PTT button, and speak in Monitor/ Call Cancel normal voice. Please keep your mouth 3~8 cm Squelch off Momentary/Call Cancel away from the microphone. - Page 9 CALL 1/CALL 2/CALL3/CALL4 B) The working channel of the radio will revert to the following Press the side button set as CALL 1/CALL 2/CALL3/CALL4 channels automatically when you press PTT button during transmit the stored coding. scanning. The dealer can select one among the following six options.: Lone Work 1) Start channel...
- Page 10 channel, either. Squelch off Momentary/Call Cancel After exiting scanning mode and entering it again, the temporarily Press the button set as Squelch off Momentary to open the deleted channel will be added in the scanning list again. squelch; release it to exit. When in selective call state, press this key to exit selective call Call Forward Press this key to enter mode.
-
Page 11: Vox (Voice Operated Transmission)
GPS GPS Position Annunciation (Optional) twice and the radio enters cloning mode. The radio can annunciate the information of the current position 2) Press once the PTT button on the host radio, and then the sub such as longitude and latitude through the microphone when the radio to receive data will enter Wired Cloning Mode. -
Page 12: Battery Save
a) Before the time-out timer stops transmitting, the radio sounds current channel number will sound. pre-alert tone. b) After the alarm tone, if the transmitting time is longer than the CTCSS/DCS preset time limit, the time-out timer will be activated. The dealer can set CTCSS/DCS on the radio channels to ignore calls on the same channel from irrelevant radios. -
Page 13: 5-Tone Signalling
2TONE Signalling The dealer can set DTMF Signalling into encoding sequence. If DTMF is set in the encoding template, press the corresponding This function can be enabled or disabled by dealers through programmable button Call 1 Call 2 , Call 3 , or Call programming software. -
Page 14: Trouble Shooting
The battery MAJOR SPECIFICATIONS The battery life is finished; please replace it power consume with a new battery pack. quickly after PT7200 charging. Frequency Range (1) 136~174 (2) 400~470 The frequency or QT/DQT Signallings are not Cannot talk to or... -
Page 15: Settings
Receiver Sensitivity Narrow Band 0.28ìV / QT/DQT QT/DQT Transmitting Receiving Channel User Channel Power Decode En code Frequency Frequency Spacing Solution Wide Band 0.25ìV Adjacent Channel Selectivity 60dB (N)/ 70dB (W) Intermodulation Reject Ratio 65dB Maximum AF Output Power 1000mW Number of Channels Battery Standard DC 7.4V... - Page 16 GPS GPS Position Annunciation Scan GPS ID GPS ID Annunciation Temporarily Delete Noise Channel Transport GPS GPS Time Annunciation High/Low Power Switch Squelch Level Check Monitor Momentary/Call Cancel Side Button 2 Monitor/ Call Cancel Null Squelch Momentary/Call Cancel Channel Annunciation Squelch / Call Cancel Whisper Monitor/ Call Cancel...
- Page 17 1588 your radio(s). Please contact your dealer for details. We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, China Declare on our sole responsibility that this equipment complies with...
Need help?
Do you have a question about the PT7200 and is the answer not in the manual?
Questions and answers