Kirisun PT8000 Instruction Manual
  1. Manuals
  2. Brands
  3. Kirisun Manuals
  4. Transceiver
  5. PT8000
  6. Instruction manual

Kirisun PT8000 Instruction Manual

Vhf/uhf fm mobile transceiver
Hide thumbs Also See for PT8000:
Table of Contents

Advertisement

Quick Links

See also: Service Manual

INSTRUCTION MANUAL

FM MOBILE TRANSCEIVER
PT8000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT8000 and is the answer not in the manual?

Questions and answers

Related Manuals for Kirisun PT8000

Summary of Contents for Kirisun PT8000

  • Page 1: Instruction Manual

    INSTRUCTION MANUAL FM MOBILE TRANSCEIVER PT8000...
  • Page 2 NOTE INSTRUCTION MANUAL PT8000 VHF/UHF MOBILE RADIO MANDATORY SAFETY INSTRUCTIONS TO INSTAL- -LERS AND USERS Use Only manufacturer or dealer supplied antennas. Antenna minimum safe distance: 108 cm. Antennas used for this transmitter must not exceed an antenna gain of 3 dB.
  • Page 3 Closer than the above indicated minimum safe dista- nce to the antenna (i.e. 108cm). To comply with current FCC RF Exposure limitations, the antenna must be installed at or exceeding the minim-- um safe distance indicated above, and in accordance with the requirements to the antenna manufacturer or supplier.

  • Page 4: Table Of Contents

    Caution: CONTENTS Changes or modifications not expressly approved by the 1. Package-opened Inspection and Installing........2 party responsible for compliance could void the user's 2. Radio Overview................4 authority to operate the equipment. 3. Basic Operation................6 4. Programmable Button Function............7 5. Radio call..................8 6.

  • Page 5: Package-Opened Inspection And Installing

    . Package-opened Inspection and Installing Preparation 1.2.1 Connection of Power Cable Please check the host in the package and the supplied accessories in First of all, please check whether there is a hole for the power the following table before using. Any articles are found lost or damaged, cable on the insulating board.

  • Page 6: Radio Overview

    Connect the antenna and the power cable to the radio. P1button (programmable button) P2 button (programmable button) Install the microphone hanger at the position easy to use, with P3button (programmable button) 2 M4*16 self-tapping screws. (The microphone and its cable should PTT button (on the hand microphone) be fixed at the position not affecting safe driving.) Press the PTT button first, and then speak to the microphone to transmit the...

  • Page 7: Basic Operation

    in th e normal voice. Please keep the microphone about 3 or 4 cm Display Description far from your mouth. After speaking, please loosen the PTT button. Displays "P " when the radio enters the PC 5. Receive: Programming Mode. The radio will return to the receiving state after you loosen the Displays "t "...

  • Page 8: Radio Call

    6. Talk-around the current sending power is low. In the communication network, you can expand communication 12.Monitor Hold to disable CTCSS/DCS signaling according to the range through the repeater, but when the mobile radio is out of the momentary setting to resume normal operation. communication range, you can connect with other radio in the 13.Monitor Press to disable CTCSS/DCS signaling to receive signals...

  • Page 9: Public Address

    8. Public Address software or send Your own ID or background voice to your partner or the system. Press the button programmed for "Public Address", "b" will be In the Emergency Alarm Mode, press the button "Emergency displayed.Press the PTT button, the voice from the MIC of the Alarm Off"...

  • Page 10: Trouble Shooting Guide

    clone mode. If the function is disabled, it will enter the user mode. Problem Solution 2. Connect the slave radio with the wired clone cable first, and then B. The high-frequency amplifying tube Q18 is broken. Please change it. turn on. C.
  • Page 11 DECLARATION NOTE OF CONFORMITY 0678 We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, China Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment Directive,1999/5/EC,and that any applicable Essential Test Suits measurement have been performed.

Table of Contents