Superior DRL4543TEN Installation And Operation Instructions Manual page 31

ON
OFF
Cont.
ROOM
Pilot
°
SET
S M T W T F S
P1 PROGRAM
:
AM
P2
PM
A B
AUX
MODE/SET
MODE/SET
DOWN
Button
Button
Figure 49 - Touch Screen Settings
Day and Time Display
• The current day of week and time of day will be continuously dis-
played in the TIME/PROG Zone (except during Setup operations).
• The day of week will be displayed as one of the following: S, M,
T, W, T, F, S
• The time of day will be in 12-hour AM, 12-hour PM format.
Midnight will be displayed as 12:00am.
• Day/Time Setup:
• Press and hold the MODE Zone or the MODE/SET Button
for 5 seconds to enter Day/Time Setup.
• Press the UP or DOWN Buttons to adjust the day of week
(press the MODE/SET Button or wait for 15 seconds for ad-
justment to be accepted, then enter hour of day adjustment).
• Press the UP or DOWN Buttons to adjust the hour of the
day. The time will advance in 1-hour increments; AM and
PM will change when the hour advances to 12:00 midnight
and 12:00 noon respectively (press the MODE/SET Button
or wait for 15 seconds for adjustment to be accepted, then
enter minute of hour adjustment).
• Press the UP or DOWN Buttons to adjust the minute of the
hour. The time will advance in 1-minute increments (press
the MODE/SET Button or wait for 15 seconds and the
transmitter will exit Day/Time Setup and return to normal
operation).
• LCD Displays – when in Day/Time Setup:
MODE Zone: Blank
ROOM TEMP Zone: Blank
SET TEMP Zone: Blank
LIGHT Zone: Blank
FAN Zone: Blank
TIME/PROG Zone: Day of Week, or Time of Day will Flash
AUX Zone: Blank
FLAME Zone: Blank
126718-01C
REMOTE CONTROL OPERATION Continued
MODE Zone
ROOM TEMP
Zone
°
SET TEMP Zone
(Unused)
USB
P2 TIME/PROG.
P2
Zone
LIGHT Zone
FLAME Zone
AUX Zone
(Unused)
FAN Zone
(Unused)
UP Button
Superiorfireplaces.US.com
• Temperatures may be displayed in degrees F (factory default)
or degrees C. Press the up and down buttons simultaneously
to change between degrees F. and C.
MODES OF OPERATION
Operation modes:
• MANUAL OFF
• MANUAL ON
The modes may be cycled in the order above by pressing the MODE
Zone or the MODE/SET Button.
MANUAL OFF MODE
• Transmits flame OFF command.
• LCD Displays:
• MODE Zone: OFF is displaye
• ROOM TEMP Zone: Measured temperature is displayed
• SET TEMP Zone: Blank
• LIGHT Zone: LIGHT and light setting level is displayed
• FAN Zone: Blank
• TIME/PROG Zone: Current day indicator and current time
is displayed
• AUX Zone: Blank (AUX function is omitted on this control)
• FLAME Zone: Blank
MANUAL ON MODE:
• Transmits flame ON command
• LCD Displays:
• MODE Zone: ON is displayed
• ROOM TEMP Zone: Measured temperature is displayed
• SET TEMP Zone: Blank
• LIGHT Zone: LIGHT and light setting level is displayed
• FAN Zone: FAN and fan setting level is unused
• TIME/PROG Zone: Current day indicator and current time
is displayed
• AUX Zone: Blank (AUX function is omitted on this control)
• FLAME Zone: A&B Flame Icons and flame setting level
numbers are displayed
FLAME - A (OR MAIN) ADJUSTMENT
• Transmits a flame height setting command to the control module
to adjust the Flame-A height.
• Available settings are 1-7 with a factory default of 7. If the Flame-
A setting is changed during operation (either manually or auto-
matically), the control will remember and use the adjusted setting
on subsequent manual ON cycles (Flame-A setting memory).
• While in MANUAL ON, or PROGRAM ON modes, press the FLAME
Zone to enter Flame-A Adjustment, then press the UP or DOWN
buttons to raise and lower the flame; press the MODE/SET Button
or wait for 15 seconds to accept the new setting.
• LCD Display: When setting the Flame-A height, the Flame-A
icon, and Flame-A setting number will flash in the FLAME Zone.
31