Related Manuals for Hougen HMD909
Summary of Contents for Hougen HMD909
- Page 1 HMD909 & HMD909AUS PORTABLE MAGNETIC DRILLS OPERATOR’S MANUAL FOR USE WITH “12,000-SERIES” HOUGEN CUTTERS CUTTERS ® ® ®...
-
Page 2: Welcome To Hougen
Hougen, Hougen Logo, and Punch Pro are proprietary trademarks of Hougen Manufacturing Inc. Ogura and the Ogura logo are proprietary trademarks of Ogura & co., Ltd. Vac-Pad are propriety trademark of Drillmate PTY, Ltd. -
Page 3: Safety First
(10569) and then screw the handles into the 3. Complete and mail the Product Registration Card hub. Do not overtighten. NOW. It is important that Hougen Manufacturing, Inc. 8. Your Magnetic Drill was factory adjusted prior to shipping. have a record of product ownership. -
Page 4: Important Safety Instructions
Keep Work Area Clean 12. Non-Conforming Cutting Tools Cluttered areas and benches invite injuries. Your Mag Drill is designed to use Hougen Cutters. Keep dirt and chips from under the Cutter area. The use of drilling tools having different shank styles... -
Page 5: Safety Switch Indicator Light
Do not operate tool if switch does not turn The Safety Switch Indicator Light is a Standard Safety it on and off. Feature on HMD909 Models of magnetic drills. Its purpose is to inform the user that an unsafe condition exists. 22. Stay Alert Watch what you are doing and use common sense. -
Page 6: Operating Instructions
Operating Instructions 7. Make certain that cutter is clear of workpiece and turn Always remember that the magnet’s holding power is motor On by pressing the motor START button. directly related to the workpiece thickness and surface 8. Feed the cutter slowly into workpiece. Only after cutting condition. - Page 7 INSTALLING HOUGEN CUTTER IN ARBOR 1. Disconnect power source. 2. Lay drill on its side with feed handles up to be sure arbor clears table if unit is in normal operating position. 3. Turn feed handles until cutter mounting set screws are exposed and then completely remove the set screws.
- Page 8 COOLANT BOTTLE ASSEMBLY - P/N: 05060 Attach Coolant Bottle ������� ���� �� � ��� Insert hose through nut and tighten, using 7/16" wrench. DO NOT OVER TIGHTEN. Make sure nut is seated properly in coolant bracket...
-
Page 9: Drill Maintenance
Drill Maintenance In order to minimize wear on moving parts and insure Coolant bottle must be attached to inducer under smoother operation and longer life, the following pressure with shut-off valve open to lubricate inducer maintenance should be done periodically, based on use. o-rings whenever motor, is running. -
Page 10: Hookup Diagram
HOOK UP DIAGRAM Motor Black Black from Circuit Board (P3) White from Circuit Board (P4) Motor White Blue from Power In (White) Circuit Board (P2) Power In (Black) Brown from Circuit Board (P1) Safety Switch (Blue-J4) J1 J2 LED (J3) Ground (Green) Ground (Green) From Magnet... -
Page 11: Panel Components
Panel Components Panel Assembly Panel Assembly 05293 - HMD909 05306 - HMD909Aus 05292 (HMD909 Models) 05289 04671 04891 04893 05288 05302 04495Aus (Aus Models) White 04879 04878 Wire 04881 04877 Note: When inserting LED into wiring harness make sure red anode lines up... -
Page 13: Motor Parts List
Motor Bolt Sequence 1. Tighten bolts in the sequence shown to 5 - 10 in/lb. 2. Retighten bolts in the same sequence to 35 - 40 in/lb. Motor Parts List Part # Description Part # Description 01087 Armature 230V 40281 Motor Slug 01088 Field 230V... - Page 14 HMD909 EXPLODED VIEW...
-
Page 15: Parts List
PARTS LIST Part # Description Part # Description 40230 Gear Rack 04375 Arbor Sup. Bracket Assy 40231 Bushing Bronze 04532 Feed Handle Knob 40234 Thrust Washer 04885 Safety Switch Assy 40237 Set Screw 1/4-28 04909 Safety Switch Bracket 04961 Plunger Assy 40242 Arbor Assy 05049...
Need help?
Do you have a question about the HMD909 and is the answer not in the manual?
Questions and answers