Related Manuals for Denver DDP-300
Summary of Contents for Denver DDP-300
- Page 1 Digital Cordless Telephone (DECT) with Caller ID & Speakerphone Function DENVER DDP-300 USER’S MANUAL Please read before use and save...
- Page 2 This equipment is not designed for making emergency telephone calls when power fails. Alternative arrangements should be made for access to emergency services. Caller ID Caller ID available only user subscribes caller Id service and incoming call with caller ID display Model:DDP-300...
-
Page 3: Table Of Contents
4.12 Locating a misplaced handset (paging) 5 THE PHONE BOOK 5.1 Using the alphanumeric keypad 5.2 Adding a number and a name to the Phone Book 5.3 Looking up a number in the Phone Book 5.4 Calling a programmed number from the Phone Book Model:DDP-300... - Page 4 8.5 Transferring a call to another handset 8.6 Receiving an external call during an internal call 8.7 Conference call (two internal DECT handsets and one external caller) 8.8 Selecting a base unit 8.9 Automatic / Manual Selecting a base unit Model:DDP-300...
- Page 5 9 TROUBLE SHOOTING 10 TECHNICAL CHARACTERISTICS 11 WARRANTY Model:DDP-300...
-
Page 6: Introduction
10 Clean the telephone with a slightly damp cloth or with an anti-static cloth. Never use cleaning agents or abrasive solvents. 1.3 Packing List Handset Base Station Adaptor Line Cord 2 PCS Battery 600mAH Manual Model:DDP-300... -
Page 7: Instruction
2 Line key 3 Up/Hands free key 4 Programming 5 Phonebook key 6 Redial key 7 Microphone 8 Volume/Ringer key VOL 9 Alphanumeric keys 10 Delete/Mute key 11 Down/Flash key 12 Base 13 Paging key base 14 Line/Charge indicator (LED) Model:DDP-300... -
Page 8: Display (Lcd) Symbol
- this symbol appears on the display when one makes or receives a call. 10 Symbol display ( - this symbol means that the ringer is turned off. When one receives a call, the telephone does not ring. The telephone will ring when one receives an internal all. Model:DDP-300... - Page 9 - this symbol appears when you browse the numbers in the Phone Book. 14 Symbol display ( - this symbol appears when you have received a voice mail message (this function will work only if supported by your voice mail company). Model:DDP-300...
-
Page 10: Installation
LCD display. With one handset and one base unit the indicator is "1". 3.3 Handset charger 1 Put the handset on the base unit for 15 hours. The Line/Charge indicator (LED) on the base unit will light up. Model:DDP-300... -
Page 11: Low Battery Warning
If the handset is out of range of the base unit, a warning signal will sound. 'SEARCHING' appears on the display and the symbol blinks on the display. Move closer to the base unit. As soon as you are back within range of the base unit, a signal sounds and the symbol stops blinking. Model:DDP-300... -
Page 12: Operation
4.4 Receiving incoming call Press the Line key 4.5 To hang up a call After finishing your call, press the Line key to hang up or put the handse back on the base unit. Model:DDP-300... -
Page 13: Redialling The Last Number Dialed
Press the same button to deactivate the handsfree function. Note : When you are calling in handsfree mode and you want to change the volume, press the Volume button . Model:DDP-300... -
Page 14: Recall
If you cannot find the handset, briefly press the Paging key on the base unit. All handsets subscribed with the base unit will sound a signal so you can locate them is placed handset. To stop the signal, briefly press the Line key on the handset. Model:DDP-300... -
Page 15: The Phone Book
4 Press the Up or Down key repeatedly until 'ADD NEW' appears on the display. 5 Press the Programming key . 'NAME' appears on the display. 6 Enter the name. Use the alphanumeric keys. 7 Press the Programming key Model:DDP-300... -
Page 16: Looking Up A Number In The Phone Book
5 After finishing your call, press the Line key to hang up or put the handset back on the base unit. 5.5 Changing a name or number in the Phone Book 1 Press the Programming key Model:DDP-300... -
Page 17: Deleting Name And Number From The Phone Book
8 Press the Up or Down key until the number you want to delete appears on the display. 9 Press the Delete key 10 'DELETE ' appears on the display. 11 Press the Programming key to confirm that you want to delete it. Model:DDP-300... -
Page 18: Handset Setup
RING SEL MELODIES EXTERNAL VOLUME DIRECT YEAR MONTH DATE/TIME HOURS MINUTES TONE DIAL MODE PULSE ENGLISH SWEDISH SETTING LANGUAGE FINNISH NORWEIGAN ITALIAN AUTO BASE SEL MANUAL REMOVE HS RECALL BARRING BAR NUM PIN CODE RESET BASE SUB POWER OFF Model:DDP-300... -
Page 19: Turning Key Click On/Off
You can choose from 5 levels. The telephone is set to level '3' by default. During a call, you can change the volume as follows: 1 Press the Volume/Ringer key VOL . 2 The volume level currently set appears on the display. Model:DDP-300... -
Page 20: Setting The Ring Volume Level
If you want, you can change the ringer melody for an incoming call. You have 9 ringer melodies to choose from (1-9). By default, the ringer melody is set to '5'. 1 Press the Programming key 2 Press the Up or Down key repeatedly until 'RING SEL' appears on the display. Model:DDP-300... -
Page 21: Setting The Language
You can program the handsets to bar calls to certain telephone numbers so that for instance '00' international numbers cannot be called. Up to 5 numbers (of max. 5 digits) can be barred. To do this, do the following: Model:DDP-300... -
Page 22: Changing The Pin Code
'PIN CODE' appears on the display. 5 Press the Programming key . 'OLD CODE' appears on the display. 6 Enter the old PIN code. Use the number keys. 7 Press the Programming key . 'NEW CODE' appears on the display. Model:DDP-300... -
Page 23: Direct Call
1 Press the Programming key 2 Press the up or down key until 'DIRECT' appears on the display. 3 Press the mute-key for 2 seconds 4 DIRECT ON' appears on the display To turn if OFF: Quick press the Programming key twice Model:DDP-300... -
Page 24: Default Settings (Reset) Of The Parameters
3 Press the Programming key 4 Press the Up or Down key repeatedly until 'RESET' appears on the display. 5 Press the Programming key . 'PIN' appears on the display. 6 Enter your PIN code. Press the Programming key Model:DDP-300... -
Page 25: Caller Id/Clip
If the Call List is empty and you press the Up key , three beep tones will sound. 7.3 The Call List The calls received are stored in the Call List (max. 30 numbers). Model:DDP-300... -
Page 26: Calling A Number From The Call List
1 Press the Up key to go to the Call List. 2 Keep the Delete key pressed until 'DELETE ALL' appears on the display. 3 Press the Programming key to confirm your selection or the Delete key cancel. 4 All calls are deleted. Model:DDP-300... -
Page 27: Multiple Handset And Base Operation
7 Press the Programming key . 'PIN' appears on the display. 8 Enter the 4-digit PIN code of the base unit in (default PIN code is '0000'). 9 Press the Programming key . The handset is subscribed to the base unit. Model:DDP-300... -
Page 28: Removing Subscription Of A Handset To A Base Unit
8.4 Receiving an internal call This function only works if multiple handsets are subscribed to the base unit! 1 Press the Line key to accept the internal call. 2 During the call, 'INT', the handset number of the caller and the symbol Model:DDP-300... -
Page 29: Transferring A Call To Another Handset
5 Dial the number of the handset you would like to include in the call. 6 Once the handset dialled is answered, keep the '#' key pressed for 2 seconds. 7 'CONFERENCE' appears on the display. 8 Now you are connected to one external and one internal caller (conference call). Model:DDP-300... -
Page 30: Selecting A Base Unit
Before you can select a base unit, the base unit must be subscribed to the handset first. If 'NOT SUB' appears on the display, this means the selected base unit does not exist or thehandset has not been subscribed. Model:DDP-300... -
Page 31: Trouble Shooting
Telephone does not Manipulation error Remove the batteries and but react to pressing the them back in place keys Keypad lock ON Turn OFF the Keypad lock Flash(R) Key does Wrong Flash time Change the flash time not work Model:DDP-300... - Page 32 220 V / 50 Hz for the base Handset Batteries 2 rechargeable batteries AAA, NiMh 600mAh Handset autonomy 100 hours in standby Talk time: 6 hours Charging time 15 hours Normal conditions of use +5 C to +45 C Dialling mode Pulse / Tone Model:DDP-300...
- Page 33 No warranty can be claimed if the serial number on the units has been changed, removed or rendered illegible. Any warranty claims will be invalid if the unit has been repaired, altered or modified by the buyer or by unqualified, non-officially appointed service centres. Model:DDP-300...