YASKAWA VS?616G5 Owner's Manual page 79

Name
Constant
(Digital Operator Display)
No.
H4−05 Gain (terminal 23)
(Terminal 23 Gain)
H4−06 Bias (terminal 23)
(Terminal 23 Bias)
H4−07 Analog output signal level selection
(AO Level Select)
H5−01 Station address
(Serial Comm Adr)
H5−02 Communication speed selection
(Serial Baud Rate)
H5−03 Communication parity selection
(Serial Com Sel)
H5−04 Stopping method after communication error
(Serial Fault Sel)
H5−05 Communication error detection selection
(Serial Flt Dtct)
L1−01 Motor protection selection
(MOL Fault Select)
L1−02 Motor protection time constant
(MOL Time Const)
L2−01 Momentary power loss detection
(PwrL Selection)
L2−02 Momentary power loss ridethru time
(PwrL Ridethru t)
L2−03 Min. baseblock time
(PwrL Baseblock t)
L2−04 Voltage recovery time
(PwrL V/F Ramp t)
L2−05 Undervoltage detection level
(PUV Det Level)
L3−01 Stall prevention selection during accel
(StallP Accel Sel)
L3−02 Stall prevention level during accel
(StallP Accel Lvl)
L3−03 Stall prevention limit during accel
(StallP CHP Lvl)
L3−04 Stall prevention selection during decel
(StallP Decel Sel)
L3−05 Stall prevention selection during running
(StallP Run Sel)
L3−06 Stall prevention level during running
(StallP Run Level)
L4−01 Speed agree detection level
(Spd Agree Level)
L4−02 Speed agree detection width
(Spd Agree Width)
L4−03 Speed agree detection level (+/−)
(Spd Agree Lvl + −)
L4−04 Speed agree detection width (+/−)
(Spd Agree Wdth + −)
L4−05 Operation when frequency reference is missing
(Ref Loss Sel)
L5−01 Number of auto restart attempts
(Num of Restarts)
L5−02 Auto restart operation selection
(Restart Sel)
L6−01 Torque detection selection 1
(Torq Det 1 Sel)
80
Table A−4 Constants List (Cont'd)
Initial User
Setting Setting
0.50
0.0
0
1F
3
0
3
:
1
1
1.0
0
2.0
[
0.5
[
0.3
[
546
1
150
50
]
1
1
160
0.0
2.0
0.0
2.0
0
0
0
0
Not displayed for some models depending on software version No.
:
[
Setting unit and initial setting differ depending on inverter capacity.
]
Differs depending on the control method selection (A1−02).
# Differs depending on area.
Name
Constant
(Digital Operator Display)
No
.
L6−02 Torque detection level 1
(Torq Det 1 Lvl)
L6−03 Torque detection time 1
(Torq Det 1 Time)
L6−04 Torque detection selection 2
(Torq Det 2 Sel)
L6−05 Torque detection level 2
(Torq Det 2 Lvl)
L6−06 Torque detection time 2
(Torq Det 2 Time)
L7−01 Forward torque limit
(Torq Limit Fwd)
L7−02 Reverse torque limit
(Torq Limit Rev)
L7−03 Forward regenerative torque limit
(Torq Lmt Fwd Rgn)
L7−04 Reverse regenerative torque limit
(Torq Lmt Rev Rgn)
L8−01 Protect selection for internal DB resistor
(DB Resistor Prot)
L8−02 Overheat pre−alarm level
(OH Pre−Alarm Lvl)
L8−03 Operation selection after overheat pre−alarm
(OH Pre−Alarm Sel)
L8−05 Input open−phase protection selection
(Ph Loss In Sel)
L8−07 Output open−phase protection selection
(Ph Loss Out Sel)
o1−01 Monitor selection
(Monitor Select)
o1−02 Monitor selection after power up
(Power−On Monitor)
o1−03 Frequency units of reference setting and monitor
(Display Scaling)
o1−04 Frequency units of constant setting
(Display Units)
o1−05 Constant No. display selection
(Address Display)
o2−01 LOCAL/REMOTE key enable/disable
(Local/Remote Key)
o2−02 STOP key during control circuit terminal operation
(Oper STOP Key)
o2−03 User constant initial value
(User Defaults)
o2−04 kVA selection
(Inverter Model #)
o2−05 Frequency reference setting method selection
(Operator M.O.P.)
o2−06
Operation selection when digital operator is disconnected
(Oper Detection)
o2−07 Cumulative operation time setting
(Elapsed Time Set)
o2−08 Cumulative operation time selection
(Elapsed Time Run)
o2−09
Initialize mode selection
(Init Mode Sel)
Initial
Setting
150
0.1
0
150
0.1
200
200
200
200
0
95
3
0
0
6
1
0
0
0
1
1
0
48
[
:
0
0
−
0
: 2
#
User
Setting